User manual PANASONIC PT-52DL10

[. . . ] TM DLP A TEXAS INSTRUMENTS TECHNOLOGY V HDT 1080 COMPATIBLE RT SPATIALIZ STEREO 3-D i / 720p Projection Television Operating Instructions Model No. PT-52DL10 HDTV COMPATIBLE 1080 i / 720p SPATIALIZRT 3-D STEREO DLP TM A TEXAS INSTRUMENTS TECHNOLOGY For assistance, please call : 1-888-VIEW PTV(843-9788) or send e-mail to : consumerproducts@panasonic. com or visit us at www. panasonic. com (USA) For assistance, please call : 787-750-4300 or visit us at www. panasonic. com (Puerto Rico) TQBC0215-1 Important Safety Instructions WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. [. . . ] The screen size will also change if S1 detection has been set. · · · 29 VHF, UHF and CATV MENU ACTION TV/VIDEO VOLUME CHANNEL MENU ACTION TV/VIDEO VOLUME CHANNEL Power switch Remote control sensor Operation can be done from the projection TV. · Channel buttons · Volume buttons POWER 1 LIGHT Press to turn the projection TV on (see page 21). POWER ASPECT MUTE TV/VIDEO DVD VC R DTV CH AUX CBL RC 2 3 VOL TV VR S CH Press to operate the projection TV with the remote control. TV DB VOL MENU ACTION VOL INFO/RECALL Press to select the desired channel. ACTION VOL AV-ADJ CH NORMAL GAME RH-SPLIT EXIT VCR REC SEARCH STOP GUIDE SPLIT FF CH REW FREEZE TV/VCR PLAY SWAP VCR/DBS CHANNEL PAUSE 4 VOL CH Press to select the desired volume level. OPEN/CLOSE SLOW STILL 1 4 7 R-TUNE 2 5 8 0 3 6 ACTION VOL CH 9 PROG Notes: The channel number and volume level are stored even after the projection TV is turned off. Power consumption and howling of sound can be reduced if the volume level is lowered. · · 30 Cable TV ANTENNA TERMINALS ON THE BACK OF THE PROJECTION TV ANT1 SPLIT OUT ANT2 Y VIDEO PB PR L AUDIO R 1 COMPONENT 2 VIDEO 3 INPUT S-VIDEO VIDEO L TO AUDIO AMP R PROG OUT L ANT1 SPLIT OUT ANT2 AUDIO R 1 2 INPUT 3 To antenna Input Incoming Cable from Antenna or Cable TV System. INPUT OUTPUT LIGHT POWER ASPECT MUTE TV/VIDEO When the antenna cable is connected to the TV antenna terminal via a cable box or VCR, set the TV channel to CH3 or CH4. After select ANT2 in the PROGRAM CHANNELS (see page 24). This does not apply when signal is input from VIDEO INPUT. CABLE BOX DVD VC R DTV CH AUX CBL RC VR S Confirming Confirm that registration with cable TV and connection of equipment are completed. Turn the cable TV tuner and select the desired volume level. TV DB VOL MENU ACTION VOL INFO/RECALL 1 2 CBL AV-ADJ CH NORMAL GAME RH-SPLIT EXIT VCR REC SEARCH STOP GUIDE SPLIT FF POWER Press while pointing the remote control towards the cable TV tuner. Note: The remote control code number is set for Panasonic products. When peripheral equipment do not operate, reset code (see page 63, 64). REW FREEZE TV/VCR PLAY SWAP VCR/DBS CHANNEL PAUSE OPEN/CLOSE SLOW STILL 1 4 7 R-TUNE 2 5 8 0 3 6 9 PROG 3 Operate the cable TV tuner and select the desired volume level. 31 Searching for the desired channel (Channel search) SEARCH STOP When the SEARCH button is pressed during single screen. CH3 LIGHT POWER ASPECT MUTE TV/VIDEO DVD R VC DTV CH AUX CBL RC VR S TV DB VOL MENU ACTION VOL INFO/RECALL When a channel button is pressed during channel search. Number keys: Example: When 7 is pressed, channel 7 is displayed in single screen. Channel up and down keys: or button is pressed, the next When channel up or down is displayed in single screen. · · CH3 1 4 6 2 5 7 AV-ADJ CH NORMAL GAME RH-SPLIT Sound from the left screen is output from the speakers on the projection TV set. Ex. Select channel 7 CH7 EXIT VCR REC SEARCH STOP GUIDE SPLIT FF REW FREEZE TV/VCR PLAY SWAP VCR/DBS CHANNEL PAUSE OPEN/CLOSE SLOW STILL 1 4 7 R-TUNE 2 5 8 0 3 6 9 PROG SEARCH STOP When the SEARCH button is pressed during screen, PoutP or pause. CH3 CH5 When a channel button is pressed during channel search. The selected channel will be displayed on the right screen. (Freeze is deactivated) Sound from the left screen is output from the speakers on the projection TV set. CH3 1 4 6 2 5 7 Ex. Select channel 7 CH7 Channel search: Channel search displays each channel, in order, as a paused image. Channels are displayed from the left top to the right bottom in order. When it reaches the right bottom, the next channel is displayed at the left, overwriting the previously displayed channel. · · · 32 Notes: To end channel search, press SEARCH STOP. Channel search can be activated from the MENU screen. Channel search is valid only during TV mode. Playing a VCR or other peripheral equipment Confirming connections A video camera uses the Video Input 4 terminal on the front of the projection TV. VCR Video camera PC INPUT INPUT 4 S-VIDEO VIDEO L-AUDIO-R Laser Disk Player Confirm that the projection TV is in standby mode. PC INPUT INPUT 4 To S-video output or video output DVD player This equipment can also be connected to the rear terminals. See Connections for details. S-VIDEO VIDEO L-AUDIO-R To audio output Turning the power on and switching input modes LIGHT POWER ASPECT MUTE TV/VIDEO 1 2 POWER Turn the projection TV on. DVD VC R DTV CH AUX CBL RC VR S TV/VIDEO TV DB The input mode changes each time this button is pressed. (See page 51 and 52) TV 2 VOL MENU ACTION VOL INFO/RECALL AV-ADJ CH NORMAL GAME RH-SPLIT EXIT VCR REC SEARCH STOP GUIDE SPLIT FF REW FREEZE TV/VCR PLAY SWAP VCR/DBS CHANNEL PAUSE OPEN/CLOSE SLOW STILL 1 4 7 R-TUNE 2 5 8 0 3 6 9 PROG · · When playing a DVD · When playing a laser disc · When playing from a video camera When playing a video PC VIDEO 1 COMPONENT 3 VIDEO 2 1 COMPONENT 2 1 1 1 COMPONENT 1 1 VIDEO 3 VIDEO 4 1 No input mode is displayed for terminals with no equipment connected. 2 No input mode is displayed for terminals with no signal. Notes: When the remote control is unavailable, input modes can also be switched on the projection TV set using the TV/VIDEO button. [. . . ] · Is the antenna receiving any signals reflected off of mountains or buildings. · The image distorts when channels are changed. · When using 16:9 image software, there is no picture at the top and bottom of the screen (cinema vision size software, etc. ). If so, adjust screen positioning. ­ ­ · Has the screen position been changed?· Press the INFO/RECALL button. During VIDEO input, channel number is displayed until an image is displayed. [. . . ]