User manual PANASONIC PT-D10000U

[. . . ] Operating Instructions DLP® Based Projector Commercial Use Models No. PT-D10000U PT-DW10000U Read these instructions completely before operating this unit. TQBJ 0208 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLP® based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D10000U/PT-DW10000U Serial number: 2 ­ ENGLISH Contents Be sure to read the "IMPORTANT SAFETY NOTICE" and the "Precautions with regard to safety". [. . . ] Press to select "BLANKING". ADVANCED MENU DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING FRAME DELAY RASTER POSITION AUTO When correcting the right hand blanking of the screen (right) Press button to move the blanking zone to the right; button to the left. OFF DEFAULT Adjusting the input resolution ENTER MENU SELECT SUB MENU Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. 2. Press ENTER. · The "BLANKING" adjustment screen will be displayed. BLANKING UPPER LOWER LEFT RIGHT MENU SELECT ADJUST 0 0 0 0 1. Press to select "INPUT RESOLUTION". ADVANCED MENU DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING FRAME DELAY RASTER POSITION AUTO OFF DEFAULT 3. Press to select the desired item for adjustment. Press to adjust blanking. · The adjustment value for the PT-D10000U can be changed within a range of 0 to 255 vertically and 0 to 700 horizontally. · The adjustment value for the PT-DW10000U can be changed within a range of 0 to 540 vertically and 0 to 960 horizontally. When correcting the upper blanking of the screen (top) Press button to move the blanking zone upward; button to downward. ENTER MENU SELECT SUB MENU 2. Press ENTER. · The "INPUT RESOLUTION" screen will be displayed. INPUT RESOLUTION TOTAL DOTS DISPLAY DOTS TOTAL LINES DISPLAY LINES MENU SELECT ADJUST 1344 1024 809 768 When correcting the lower blanking of the screen (bottom) Press button to move the blanking zone upward; button to downward. 3. Press to select "TOTAL DOTS", "DISPLAY DOTS", "TOTAL LINES" or "DISPLAY LINES", and the press to adjust it. · Each item automatically displays a value in response to the type of the input signal. If vertical stripes appear on the screen or the image is partly missing, increase or decrease the displayed value while observing the screen to achieve the optimal value. ENGLISH ­ 61 Basic Operation How to use ADVANCED MENU (continued) Note · The abovementioned vertical stripes will not appear on the screen when all signals are input. · The picture may be distorted during the adjusting operation, but this is not a fault. · The input resolution can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. Edge blending adjustment This projector has the function to hide the seams for multi-screens. 1. Press to select "EDGE BLENDING". ADVANCED MENU DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING FRAME DELAY RASTER POSITION AUTO Adjusting the clamp position Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green. OFF DEFAULT 1. Press to select "CLAMP POSITION". ADVANCED MENU DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING FRAME DELAY RASTER POSITION AUTO MENU SELECT CHANGE 2. Press to switch "EDGE BLENDING". · The setting will change as follows each time is pressed. OFF ON USER OFF DEFAULT ENTER MENU SELECT SUB MENU 2. Press ENTER. · The "CLAMP POSITION" screen will be displayed. CLAMP POSITION POSITION MENU SELECT ADJUST 1 · OFF: When the multi-screens are not going to be used. · ON: When the tilting inside the unit is to be used for the tilting of the edge blending area. · USER: When a specific tilting is to be used for the tilting of the edge blending area. (Separate software is required to establish these settings. Press to adjust. · The value changes from 1 to 255. · The optimal value for the clamp position adjustment If dark areas are crushed: The optimal value is the point where the dark area is best improved. If the dark areas are displayed in green: The optimal value is the point where the green area becomes dark and clear. 3. [. . . ] La durée de vie de la lampe utilisée dans ce projecteur est de 2000 heures. Cependant, il est possible que la lampe soit morte (ne s'allume pas) avant ces 2000 heures, selon les caractéristiques de chaque lampe et de ses conditions d'utilisation (la durée de vie d'une lampe peut en effet être affectée par le nombre de fois où elle a été allumée et éteinte et par les intervalles qui les séparent). Il est par conséquent fortement conseillé de toujours avoir une ampoule de rechange à portée de main. Lorsqu'une lampe n'a pas été remplacée après 2000 heures d'utilisation, cette lampe sera automatiquement éteinte. [. . . ]