User manual PANASONIC PT-D7

[. . . ] 4-9) Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 How to adjust the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Automatic adjustment (AUTO SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Registration of input signal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · The adjusted value is reflected in other input signals. · Keystone distortion can be corrected to ±40° of the angle of tilt for the projector against the screen. (The range for the angle of elevation is within ±22° when using a lens with a fixed focal point, and it is within ±28° when using an LE6 lens. ) 1. Press to select "KEYSTONE". POSITION SHIFT ASPECT ZOOM CLOCK PHASE KEYSTONE DEFAULT 0 ENTER MENU SELECT SUB MENU 2. Press ENTER. · The "KEYSTONE" screen will be displayed. KEYSTONE KEYSTONE SUB KEYSTONE LINEARITY MENU SELECT ADJUST 0 0 0 3. Press to adjust the "KEYSTONE". · The value changes from -127 to 127. 4. Press to select "SUB KEYSTONE" or "LINEARITY". Press to adjust "SUB KEYSTONE" or "LINEARITY" · The value changes from -127 to 127. ENGLISH ­ 59 Basic Operation How to use ADVANCED MENU Digital cinema reality Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i, 1 080/50i and 1 080/60i signal input is applied. 1. Press to select "DIGITAL CINEMA REALITY". MENU ENTER ADVANCED MENU DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING FRAME DELAY RASTER POSITION AUTO OFF DEFAULT MENU SELECT CHANGE 2. Press to switch "DIGITAL CINEMA REALITY". · The setting will change as follows each time is pressed. AUTO OFF Fine settings are possible. MENU Press to display the MAIN MENU screen. 30p FIXED: When 480i or 1 080/60i signals are input 25p FIXED: When 576i or 1 080/50i signals are input Press to select "ADVANCED MENU". Press to display the "ADVANCED MENU" menu. MAIN MENU PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE OPTION1 OPTION2 TEST PATTERN SIGNAL LIST NETWORK SECURITY · AUTO: Performs automatic detection and cinema processing. · The optimal value for the clamp position adjustment If dark areas are crushed: The optimal value is the point where the dark area is best improved. If the dark areas are displayed in green: The optimal value is the point where the green area becomes dark and clear. 3. Press ENTER. · The "EDGE BLENDING" screen will be displayed. EDGE BLENDING UPPER START OFF WIDTH LOWER START OFF WIDTH LEFT START OFF WIDTH RIGHT START OFF WIDTH MARKER BRIGHT ADJUST MENU SELECT ADJUST 0 128 0 128 0 128 0 128 OFF Note · The clamp position can be adjusted only when the RGB signal input is applied with RGB1 and RGB2 IN. ENTER CHANGE 62 ­ ENGLISH 4. Press to specify the area to be adjusted. · · · · To joint the top: set "UPPER" to "ON". To joint the bottom: set "LOWER" to "ON". To joint the left: set "LEFT" to "ON". To joint the right: set "RIGHT" to "ON". 9. Press to select "BRIGHT ADJUST". EDGE BLENDING UPPER START OFF WIDTH LOWER START OFF WIDTH LEFT START OFF WIDTH RIGHT START OFF WIDTH MARKER BRIGHT ADJUST MENU SELECT ENTER SUB MENU 0 128 0 128 0 128 0 128 OFF 5. Press ENTER to toggle "ON" and "OFF". Press to adjust the compensation width and start position. marker · The "BRIGHT ADJUST" screen will be displayed. BRIGHT ADJUST BRIGHT INSIDE BRIGHT OUTSIDE UPPER LOWER LEFT RIGHT MENU SELECT ADJUST 0 0 0 0 7. Press to select "MARKER". EDGE BLENDING UPPER START OFF WIDTH LOWER START OFF WIDTH LEFT START OFF WIDTH RIGHT START OFF WIDTH MARKER BRIGHT ADJUST MENU SELECT ENTER CHANGE 0 128 0 128 0 128 0 128 OFF 8. [. . . ] Faire attention aux mouvements de la main lors de l'utilisation du tournevis à proximité de la lampe. Attention · L'unité de la lampe est une pièce en option. Consulter votre revendeur pour plus de détails à propos des commandes. N° de modèle de l'unité de remplacement de la lampe : ET-LAD10000 (ampoule simple), ET-LAD1000F (4 ampoules) Puissance : 250 W · Des lampes autres que celles spécifiées ci-dessus ne devront en aucun cas être utilisées. N'utiliser que les types de lampe spécifiés. Intervalle de remplacement de la lampe Toute lampe utilisée en tant que source de lumière a une durée de vie limitée. [. . . ]