User manual PANASONIC PT-D9510E

[. . . ] DLPTM based Projector Commercial Use Operating Instructions Models No. PT-D9510E PT-D9610E POWER SYSTEM SELECTOR STD RGB PROJECT OR INPUT1 INPUT2 INPUT3 BRIGHT MENU CONTRAST + ­ LENS ENTER 1 PCMUTE 2 5 8 ID ALL 3 6 9 0 4 7 ID SELECT ON SCREEN NEXT Operating Instructions Bedienungsanleitung 1-94 95-187 Read these instructions completely before operating this unit. TQBJ0085 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. [. . . ] Press the UP ( ) and DOWN ( ) arrow buttons to select CLOCK PHASE. NOTE · The clock phase can be adjusted when an RGB signal has been input with the analogue RGB module (ET-MD95RGB) Press the ENTER button. The CLOCK PHASE screen will be displayed. Use the control level buttons (+ and -) to adjust the clock phase. · The adjustment values will change from 0 (min. ) to 31 (max. ). NOTE · If the signal output from the personal computer is itself unstable, it may not be possible to obtain an optimum adjustment value. · If the TOTAL DOTS setting is incorrect, it may not be possible to obtain an optimum adjustment value. 50 Adjusting the picture position Adjustment procedure ENGLISH Press the MENU button. Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. Press the UP ( ) and DOWN ( ) arrow buttons to select SHIFT. Press the ENTER button. Press the UP, DOWN, LEFT and RIGHT ( , , and ) arrow buttons to adjust the picture position. · The on-screen display will disappear and the screen will return to the normal state. When adjusting the horizontal position If the button is pressed, the picture moves to the right. If the button is pressed, the picture moves to the left. When adjusting the vertical position If the button is pressed, the picture moves to the up. If the button is pressed, the picture moves to the down. 51 Adjusting the blanking If picture noise appears at the perimeter of the screen or a picture extends off the screen a little, adjust the blanking to fine-tune the screen. Adjustment procedure ENGLISH If the button is pressed, button is the blanking portion moves upward. If the pressed, the blanking portion moves downward. If the If the button is pressed, button is pressed, the picture moves to the right. the blanking portion moves to the left. Press the MENU button. Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. Press the UP ( ) and DOWN ( ) arrow buttons to select BLK. Press the ENTER button. Press the control level buttons ( + and - ) to select the desired BLK mode from those indicated below. UPPER, LOWER, LEFT, RIGHT Press the UP ( ) and DOWN ( ) arrow buttons to adjust UPPER and LOWER, or Press the LEFT ( ) and RIGHT( ) arrow buttons to adjust LEFT and RIGHT. · The adjustment values will change from 0 (min. ) to 511 (max. ). When adjusting the upper blanking When adjusting the lower blanking If the If the button is pressed, button is pressed, the picture moves upward. the blanking portion moves downward When adjusting the left blanking When adjusting the right blanking If the button is pressed, button is the blanking portion moves to the right. If the pressed, the blanking portion moves to the left. 52 Adjusting the clamp position · If the black portions of the picture are fractured or tinged with green, adjust the clamp position its optimum state. Adjustment procedure Press the MENU button. [. . . ] · Is the REMOTE IN 1 connector being used for external control?· Is a remote control cable being connected to the REMOTE IN 2 connector ?(in the wireless mode) · Is the power turned on at the power point?· Is the power cord disconnected Power does from the power point? [. . . ]