User manual PANASONIC PT-F200

[. . . ] Operating Instructions LCD Projector Commercial Use Model No. PT-F200NTU PT-F200U Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ0248 ENGLISH Important Safety Notice Dear Panasonic Customer: The following information should be read and understood as it provides details, which will enable you to operate the projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding the use of projectors. Before connecting, operating or adjusting this projector, please read these instructions completely and save this booklet with the projector for future reference. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. [. . . ] STARTUP LOGO will be displayed for 30 seconds. ON OFF USER Active Deactive Display the original text Settings LAMP RUNTIME You can check how long the lamp has been used. NOTE: · LAMP RUNTIME is a relevant matter for lamp replacement timing. See "Replacing the Lamp unit" on page 41. · When the lamp unit is replaced with the new one (ET-LAF100), the setting will be reset to "0". Editing the original text If you select USER, you can display the 2 lines of original text up to 40 characters in 1 line instead of the logo. TEXT CHANGE DELETE OK CANCEL ENGLISH - 34 OPTION menu POWER OFF TIMER You can set the off timer to switch off the POWER of the projector after a certain period of time automatically when no signal is detected. Press I H to select the required period from 15 to 60 minutes at intervals of 5 minutes. AUTO SETUP You can turn off the AUTO SETUP function for when the COMPUTER signal is detected. AUTO When the projector detect a COMPUTER signal, adjust the projected image position automatically for SIGNAL SEARCH, DOT CLOCK and CLOCK PHASE. Only when the AUTO SETUP button is pressed, the projected image position will be adjusted for DOT CLOCK and CLOCK PHASE. See "Remote control" on page 11. DISABLE 15 MIN. 40 MIN. BUTTON NOTE: · Usually the recommended setting is AUTO. SIGNAL SEARCH You can turn off the auto signal detecting system. ON OFF Detect the input signal from the terminals and project the image. Deactive DIRECT POWER ON You can switch the projector start up status for when the Mains lead is connected while the MAIN POWER is on, or for when the MAIN POWER is switched on while the Mains lead is connected. Press I H to select the required option. OFF The projector will start from the standby mode or the projecting mode. The projector will start from the projecting mode. NOTE: · SIGNAL SEARCH is not available when any input signal is projecting. · Usually the recommended setting is ON. INSTALLATION When installing the projector, select the projection method according to the projector position. See "Projection method" on page 15. FRONT/DESK FRONT/CEILING REAR/DESK REAR/CEILING Setting on a desk/floor and projecting from front Mounting in the ceiling and projecting from front Setting on a desk/floor and projecting from rear Mounting in the ceiling and projecting from rear ON · When the projector is started from the projecting mode, pressing the POWER button procedure is skippable. CONTROL PANEL You can turn off the function of the control panel buttons on the projector body. Press I H to select the required option. INVALID Invalidate the control panel buttons Confirmation screen will be displayed. Validate the control panel buttons VALID ALTITUDE If you use the projector at high elevation, the ALTITUDE setting need to be HIGH to set the fan speed high. Press I H to select the required option. LOW HIGH The fan speed is low. The fan speed is high. NOTE: · At 1 400 - 2 700 m (4 593 - 8 858 ft) sea level, the setting must be HIGH. · The loudness of fan noise depends on the ALTITUDE setting. ENGLISH - 35 Settings NOTE: OPTION menu CLOSED CAPTION SETTING If the input signal contains closed captions, you can turn on the feature and switch the channels. OFF ON CC1 - 4 Deactive Active Change the channels from MODE WIDE MODE You can turn ON/OFF the WIDE MODE setting. ON OFF For WIDE signals For other type of signals BLACKBOARD You can exclude the BLACKBOARD in menu items of PICTURE MODE in PICTURE menu. Press I H to select the required option. ON OFF Include the BLACKBOARD in menu items. Exclude the BLACKBOARD in menu items. NOTE: · VCR with TBC (Time Base Corrector) function is recommended for video cassette tapes. TEST PATTERN You can use the 7 different test patterns to adjust the focus of the image. See "Lens shift and positioning" on page 16. Press ENTER to display the test pattern 1. [. . . ] en haut à gauche de l'écran, et attend votre Plus de 3 000 heures réponse. Pour le supprimer immédiatement, appuyer sur n'importe quelle touche. REMARQUE: · Les durées indiquées, de 2800 et 3000 heures, sont des estimations basées sur certaines conditions et ne représentent en aucun cas des durées garanties. · Pour plus d'informations à propos des caractéristiques de l'Unité de la lampe, telles que la durée de garantie, se reporter aux instructions fournies avec l'Unité de la lampe. · Lorsque la durée d'utilisation de la lampe dépasse 3000 heures, le projecteur passera en mode de veille après environ 10 minutes d'utilisation. FRANÇAIS - 60 Procédure de remplacement Retirer et remplacer la lampe 1. [. . . ]