User manual PANASONIC PT-L104P

[. . . ] Model number: PT-L104P / PT-L520U Serial number: CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. If you are unable to insert the plug into the outlet, contact an electrician. [. . . ] AUTO2 The projector automatically distinguishes between NTSC/PALM/PAL-N signals. NOTE: B This should normally be set to "AUTO1" or "AUTO2". If the signal is of such poor quality that the correct format cannot be automatically distinguished, change the setting manually to the required TV system. CONTRAST This adjusts the contrast of the picture. Press the H button to make the picture brighter, and press the I button to make the picture darker. (Adjust the BRIGHT setting first if required before adjusting the CONTRAST setting. ) PICTURE PICTURE MODE STANDARD COLOR TEMP. STANDARD COLOR 32 TINT 32 BRIGHT 32 CONTRAST 32 SHARPNESS 2 NR 1 SIGNAL MODE 525I STANDARD SELECT ADJ ESC Color Hue Setting (color temperature) COLOR TEMP. STANDARD [ SHARPNESS Press the H button to make the picture details sharper, and press the I button to make the picture details softer. HIGH [ LOW This is used to adjust the white areas of the picture if they appear bluish or reddish. Noise Reduction (NR) (Only for PT-L104P, when SVIDEO/VIDEO/YPBPR signals are being input) If the signal is of such poor quality that picture interference appears, you can suppress this interference by adjusting the NR (Noise Reduction), except for 750p (720p), HDTV60 34 35 Basic Operation PICTURE PICTURE MODE STANDARD COLOR TEMP. STANDARD COLOR 32 TINT 32 BRIGHT 32 CONTRAST 32 SHARPNESS 2 NR 1 TV-SYSTEM AUTO1 STANDARD SELECT ADJ ESC (1080i/60) and HDTV50 (1080i/50) signals. To strengthen the effect, press the H button. To turn it off , set to "0" by pressing the I button. TV SYSTEM (S-VIDEO/VIDEO only) TINT (NTSC/NTSC 4. 43/YPBPR only) This adjusts the flesh tones in the picture. Press the H button to make flesh tones more greenish, and press the I button to make the flesh tones more reddish. TV SYSTEM AUTO1 [ AUTO2 [ NTSC [ NTSC4. 43 WHITE BALANCE R/G/B (RGB only) This is used to adjust the white areas of the picture if they appear colorised. However, if a mode which does not match the aspect ratio of the input signal is selected, it may affect the quality of viewing of the original picture. Keep this in mind when selecting the aspect ratio. B If using this projector in places such as cafes or hotels with the aim of displaying programs for viewing for a commercial purpose or for public presentation, note that if the aspect ratio (16:9) selection function is used to change the aspect ratio of the screen picture, you may be infringing the rights of the original copyright owner for that program under copyright protection laws. B If a normal (4:3) picture which was not originally intended for widescreen viewing is projected onto a wide screen, distortion may occur around the edges of the picture so that part of the picture is no longer visible. Such programs should be viewed in 4:3 mode to give proper consideration to the aims and intentions of the original program's creator. RESIZING This should normally be set to "ON". (This setting is only for signals which have lower resolutions than the LCD panels. Refer to page 56 for details. ) ON The pixel resolution of the input signal is converted to the same resolution as the LCD panels before being projected. For signals with lower resolutions, gaps in the pixels are automatically interpolated into the picture before it is projected. This may sometimes cause problems with the quality of the picture. OFF The picture signal is projected at its original resolution, with no pixel conversion. The projected picture will be smaller than normal, so adjust the zoom setting or move the projector forwards or backwards to adjust the picture size if necessary. [. . . ] REMARQUE: B Le projecteur n'est pas fourni avec un bloc de lampe de rechange. Demander les détails au revendeur. Numéro de produit du bloc de lampe: ET-LA730 ATTENTION: B Ne pas utiliser un bloc de lampe avec un numéro de pièce autre que celui indiqué ci-dessus. Avant de faire le nettoyage et l'entretien, s'assurer de débrancher la fiche du cordon d'alimentation de la prise de courant. Essuyer le boîtier avec un tissu doux et sec. Si le boîtier est très sale, imbiber le chiffon dans de l'eau avec un peu de détergent neutre, bien essorer le chiffon, puis essuyer le boîtier. Après le nettoyage, sécher le boîtier à l'aide d'un chiffon sec. [. . . ]