User manual PANASONIC PT-L511XU

[. . . ] You should note it in the space provided below and retain this booklet in case service is required. Important Information Model number: Serial number: PT-LB51NTU / PT-L511XU / PT-LB51SU WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. This LCD Projector is designed to operate on 100 V - 240 V, 50 Hz/60 Hz AC, house current only. The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. [. . . ] Only when the AUTO SETUP button is pressed, the projected image position will be adjusted for DOT CLOCK and CLOCK PHASE. See "Remote control" on page 10. NOTE: · LAMP RUNTIME is a relevant matter for lamp replacement timing. See "Replacing the Lamp unit" on page 41. POWER OFF TIMER You can set the off timer to switch off the POWER of the projector after a certain period of time automatically when no signal is detected. Press I H to select the required period from 15 to 60 minutes at intervals of 5 minutes. BUTTON NOTE: · Usually the recommended setting is AUTO. DISABLE 15 MIN. 40 MIN. SIGNAL SEARCH You can turn off the auto signal detecting system. ON OFF Detect the input signal from the terminals and project the image. Deactive NOTE: · SIGNAL SEARCH is not available when any input signal is projecting. · Usually the recommended setting is ON. INSTALLATION When installing the projector, select the projection method according to the projector position. See "Projection method" on page 16. FRONT/DESK FRONT/CEILING REAR/DESK REAR/CEILING Setting on a desk/floor and projecting from front Mounting in the ceiling and projecting from front Setting on a desk/floor and projecting from rear Mounting in the ceiling and projecting from rear DIRECT POWER ON You can switch the projector start up status for when the Power cord is connected. Press I H to select the required option. OFF The projector will start from the standby mode or the projecting mode. (The projector will start from the same status as when the power cord was disconnected. ) The projector will start from the projecting mode. ON NOTE: · When the projector is started from the projecting mode, pressing the POWER button procedure is skippable. CONTROL PANEL You can turn off the function of the control panel buttons on the projector body. · The entered password operations will appear as asterisks in the box. OK CANCEL INPUT PASSWORD You can activate the security system and the password operation will be asked to perform when the projecting mode started. Unless you perform the correct password operation, all of the button controls will be disabled except the POWER button. OFF ON Deactive Active 1. Use F G I H to specify the location of the required character. Press ENTER. The selected character will be displayed in the TEXT CHANGE box. 3. Repeat until finish your original text. If you select DELETE, you can delete a character is selected with cursor. Select OK and press ENTER to set the entered text. Select CANCEL or press MENU/RETURN buttons to return to the previous menu. NOTE: · When you activated the security system, make sure to change the password to your original for safety. · The factory default password is valid until you change the password in PASSWORD CHANGE menu. ENGLISH - 37 Settings NOTE: WIRELESS menu (PT-LB51NTU only) Remote control Control panel Items in WIRELESS menu In WIRELESS menu, the following items are available. NETWORK Select the network setting you want to use. NAME CHANGE The name for this projector can be set. INPUT PASSWORD Set to "ON" if you want password confirmation to be used when controlling the projector with a personal computer by means of the wireless network. PASSWORD CHANGE Passwords can be changed. WEB CONTROL To control the projector with a personal computer by means of the wireless network, set the "WEBCONTROL" to "ON". [. . . ] L'intervalle de remplacement de la lampe prévu est de 2 000 heures; il est toutefois possible qu'il faille remplacer la lampe avant ce délai en raison d'éléments variables comme les caractéristiques particulières de la lampe, les conditions d'utilisation et l'environnement d'installation. Il est recommandé de toujours avoir un bloc de lampe de rechange prêt à l'emploi. La lampe s'éteindra automatiquement après environ 10 minutes lorsque la limite de 2 000 heures d'utilisation est atteinte, car le risque d'explosion de la lampe devient beaucoup plus grand passé cette limite. A l'écran Indication Indicateur LAMPE REMPLACER LA LAMPE «REMPLACER LA LAMPE» est affiché en Plus de 2 800 heures haut à gauche de l'écran pendant 30 secondes. [. . . ]