User manual PANASONIC PT-L520U

[. . . ] R LCD Projector Commercial Use Operating Instructions Model No. PT-L720U PT-L520U R Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ 0104-2 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. [. . . ] If the optimum setting is not obtained when AUTO SETUP is carried out, adjust by the following procedure. Use the F and G buttons on the projector or remote control unit to select an item, and then use the I and H buttons to change the setting for that item. For items with bar scales, press the ENTER button or the I or H buttons to display the adjustment screen, and then use the I or H buttons to make the adjustment. When an RGB/YPBPR signal is being input VERTICAL POSITION Press the I button to move the picture down, and press the H button to move the picture up. SIGNAL MODE (RGB/YPBPR only) This displays the type of signal which is currently being projected. Refer to the table on page 56 for details on each type of signal. DOT CLOCK (RGB only) Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. If this happens, use the I and H buttons to adjust so that any such noise is minimised. Projecting sRGB-compatible pictures sRGB is an international color reproduction standard (IEC61966-2-1) established by the International Electrotechnical Commission (IEC). If you would like the colors in sRGBcompatible pictures to be reproduced more faithfully, make the following settings. # Press the F or G button to select "PICTURE MODE", and then use the I or H button to select "NATURAL". $ Press the STANDARD (STD) button on the remote control unit. % Press the F or G button to select "COLOR TEMP. ", and then use the I or H button to select "STANDARD". NOTE: B sRGB is only enabled when RGB signals are being input (when LAMP POWER has been set to "HIGH"). CLOCK PHASE (RGB/YPBPR only) Adjust the DOT CLOCK setting first before carrying out this adjustment. Use the I and H buttons to adjust so that the noise level is least noticeable. NOTE: B If signals with a dot clock frequency of 100 MHz or higher are being input, interference may not be completely eliminated when the DOT CLOCK and CLOCK PHASE adjustments are carried out. POSITION H-POSITION 64 V-POSITION 32 DOT CLOCK 32 CLOCK PHASE 16 ASPECT 4:3 RESIZING ON STANDARD SELECT ENTER ESC When an S-VIDEO/VIDEO signal is being input POSITION H-POSITION 32 V-POSITION 16 ASPECT 4:3 RESIZING ON STANDARD SELECT ENTER ESC HORIZONTAL POSITION Press the I button to move the picture to the left, and press the H button to move the picture to the right. 36 37 Basic Operation ASPECT This setting is only for an S-VIDEO/ VIDEO signal and a YPBPR signal in 525i (480i), 525p (480p) and 625i format. S4:3 The size of the input signal is compressed to 75% and projected. (This is useful for projecting a picture with a 4:3 aspect ratio onto a 16:9 screen. ) ASPECT AUTO [ 4:3 [ 16:9 [ S4:3 AUTO (S-VIDEO only) When an S1 video signal is input to the S-VIDEO terminal, the aspect ratio is changed automatically to project a 16:9 picture. 4:3 The input signal is projected without change. 16:9 The picture is compressed to a ratio of 16:9 and projected. When a 4:3 signal is being input [ When a squeezed signal is being input. (The projected image is contracted horizontally) [ S1 video signals B S1 video signals are a type of video signal with an aspect ratio of 16:9 which include a detector signal. This detector signal is output by some sources such as wide-vision video decks. If the AUTO setting above is selected, this projector will recognise the detector signal and automatically switch the aspect ratio to 16:9 in order to project the picture. NOTE: B This projector is equipped with an aspect ratio selection function. However, if a mode which does not match the aspect ratio of the input signal is selected, it may affect the quality of viewing of the original picture. Keep this in mind when selecting the aspect ratio. [. . . ] Si un chiffon traité chimiquement est utilisé, lire les directives fournies avec le chiffon avant de l'utiliser. Ne pas essuyer la lentille avec un chiffon poussiéreux ou pelucheux. Si de la poussière ou de la peluche se dépose sur la lentille, elle sera agrandie et projetée sur l'écran. Utiliser une poire à air pour nettoyer toute poussière et peluche de sur la surface de la lentille, ou utiliser un chiffon doux pour retirer toute poussière ou peluche. 64 65 Others Affichage à l'écran Témoin d'alarme de l'indicateur de la lampe Plus de 1 800 heures Plus de 2 000 heures Affiché pendant 30 secondes. [. . . ]