User manual PANASONIC PT-L556U

[. . . ] The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. Important Information Model number: PT-LB90NTU/PT-LB90U/PT-L556U/PT-LB75VU Serial number: WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. This LCD Projector is designed to operate on 100 V - 240 V, 50 Hz/60 Hz AC, house current only. Power Supply: CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. [. . . ] The function becomes effective only when certain signals below are input. (VGA60, 480i, 576i, 480p, 576p, 1 080/60i, 1 080/50i, 720/60p, 720/50p) Select the signals to be input to the COMPUTER1 and COMPUTER2 IN terminal. Change setting AUTO RGB YPBPR Change setting Note z You must set to OFF when projecting a moving image. Automatic adjustment For RGB signals For YPBPR signals NOISE REDUCTION You can switch the automatic noise reduction system on/off. (Available with signals of S-VIDEO/VIDEO only) Change setting OFF ON Note z NOISE REDUCTION is set active when the selected Change setting No noise reduction Automatic noise reduction input signal has less noise. Applying noise reduction may affect the image quality, if so, set to OFF. ENGLISH - 31 Settings POSITION POSITION menumenu Navigating through the MENU (Æpage 27), select POSITION from the main menu and then select the required item from the sub-menu. z Set the selected item with buttons. SHIFT SHIFT H V 0 0 Remote control Control panel Horizontal (H): Press buttons to move the image horizontally. Vertical (V): Press buttons to move the image vertically. Remarks z The image cannot be moved while network signals z Press buttons to move the image. are input. REALTIME KEYSTONE If the projector is aligned non-perpendicularly to the screen, or if the projection screen has an angled surface, the keystone will be corrected automatically. Change setting ON OFF Active Deactive Change setting SHIFT V (Available with signal of network only while ASPECT is set to H FIT) Press buttons to move the image vertically. DOT CLOCK If you have interference patterns of the projected image, which is sometimes referred to as moire or noise, you can minimize it by pressing buttons to adjust the clock frequency. (Available with signal of RGB (Still image) only). KEYSTONE If you need to correct the angle of the projection even when the REALTIME KEYSTONE is activated, you can correct the keystone manually. Image Operation Note z DOT CLOCK needs to be adjusted before adjusting Settings Remarks z You can correct the distortion ±30 ° from the plane. the CLOCK PHASE. CLOCK PHASE If you require further adjustment for the same reason as the DOT CLOCK adjustment, you can fine adjust the timing of the clock. (Available with signals of RGB/ YPBPR only) Press buttons to adjust. Change setting Change setting You can choose to display or not to display the warning massages. ON OFF Warning messages will be displayed No display J INPUT GUIDE When you change the input method, the guidance appears in the upper right corner of the screen. The following display methods are available. DETAILED OFF SIMPLE Display the input method by graphic. The INPUT GUIDE will go out after 10 seconds without any operation. The INPUT GUIDE will go out after 5 seconds without any operation. Note z When the WARNING MESSAGE is set to OFF, use the projector with utmost care due to the most of warning messages will not be displayed. CLOSED CAPTION SETTING If the input signal contains closed captions, you can turn on the feature and switch the channels. J CLOSED CAPTION OFF ON Deactive Active Settings Remarks z If you select the computer terminals which have no J MODE CC1 - 4 Remarks z VCR with TBC (Time Base Corrector) function is signals while INPUT GUIDE is set to DETAILED, the computer connection guidance will be displayed. If you want to turn off the guidance, select SIMPLE or OFF. Change the channels CC1 - 4 Q Computer connection guidance You can switch the signals which output from the COMPUTER1/COMPUTER2 terminal by pressing the following computer key commands. Manufacturer Panasonic NEC Acer HP SHARP TOSHIBA lenovo SONY Image output selection command Manufacturer DELL EPSON FUJITSU Image output selection command recommended for video cassette tapes. + + + + Apple + 36 - ENGLISH DISPLAY OPTION menu STARTUP LOGO You can set to display the Panasonic logo, your own image or Pre-set letters, when starting up the projector. Change setting ON TEXT USER OFF Change setting 4 ) Select OK and press the ENTER button to set the entered text in a box. 5 ) Select OK again and press the ENTER button. Select CANCEL or press the MENU/RETURN button to return to the previous menu without setting. Display "Panasonic" logo Display the original text Display the image registered by user No display AUTO SETUP You can turn off the automatic AUTO SETUP adjustment system. Change setting Change setting Remarks z If TEXT is selected, the input letters are displayed when starting up the projector. You can display 2 lines of original text which contain up to 40 characters each. [. . . ] Il est recommandé de faire remplacer l'unité de lampe par un technicien qualifié et de contacter un centre technique agréé. J Remarque sur le remplacement de l'unité de la lampe z Manipuler l'unité de la lampe avec prudence car elle z z z z contient du verre. Si elle tombe ou qu'elle reçoit un choc, elle pourrait s'endommager ou éclater. Si vous souhaitez jeter la lampe usagée, veuillez vous renseigner auprès des autorités locales compétentes ou de votre distributeur pour connaître la bonne méthode. Préparer un tournevis cruciforme. [. . . ]