User manual PANASONIC PT-L797PWUL

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PANASONIC PT-L797PWUL. We hope that this PANASONIC PT-L797PWUL user guide will be useful to you.

Lastmanuals help download the user guide PANASONIC PT-L797PWUL.

Download

Manual abstract: user guide PANASONIC PT-L797PWUL

Detailed instructions for use are in the User's Guide.

 [. . . ] The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. Model number: Serial number: PT-L797PWUL / PT-LB75NTU/PT-LB80U/PT-LB75U

Important Information

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,  DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. This LCD Projector is designed to operate on 100 V - 240 V,  50 Hz/60 Hz AC,  house current only.  [. . . ] For a better quality image,  installing the projector with a minimum of distortion is recommended. · The distortion of the Main menu screen is not correctable. · The result of the keystone correction will affect the aspect ratio and the size of the image. 

16:9

S4:3

AUTO

Selectable options vary according to a input signal. 

4:3
The input signal will be projected in 4:3 ratio. 

POSITION
You can move the projected image for fine adjustment. Press I H to move horizontally and F G vertically. (Available with signals of VIDEO/S-VIDEO/RGB/YPBPR only)
POSITION H V
0 0

ENGLISH - 32

POSITION menu
16:9
The squeezed signal will be projected in 16:9 ratio. 

THROUGH
The image will be projected without any size adjustment. 

S4:3
The input signal will be sized down 75 % and projected. S4:3 mode is effective when projecting 4:3 image on to a 16:9 screen. 

AUTO
The signal which contains an identifying signal will be detected and automatically project the image in proper ratio. 

NOTE:
· WIDE MODE in OPTION menu should be ON when projecting WIDE signals. · If you project an image with an unmatched aspect ratio,  the image may distort or some portions may be cropped. Select an aspect ratio which preserves the intention of the image creator. · The order of ASPECT types is defined not only by the input method but also by the input signals. See "List of compatible signals" on page 44. · If you project a copyrighted image enlarged or distorted by using ASPECT function in commercial use in a public place,  such as a restaurant or hotel,  you might infringe on the copyright of the creator which is protected by copyright law. 

FRAME LOCK
If the projected image is degraded,  you can activate FRAME LOCK for synchronisation. See "Remote control" on page 14. 

NOTE:
· When no input signal is detected,  the function is disabled. · The ECO-MODE setting is recommended when higher luminance is not required such as in a small room. BUTTON

LAMP RUNTIME
You can check how long the lamp has been used. 

NOTE:
· AUTO setting is recommended. 

NOTE:
· LAMP RUNTIME is a relevant matter for lamp replacement timing. See "Replacing the Lamp unit" on page 41. · When the lamp unit is replaced with the new unit,  the setting need to be reset to "0". 

SIGNAL SEARCH
You can turn off the auto signal detecting system. 
ON OFF Detect the input signal from the terminals and project the image. Deactive

POWER OFF TIMER
You can set the off timer to switch off the power of the projector after a certain period of time automatically when no signal is detected. Press I H to select the required period from 15 to 60 minutes at intervals of 5 minutes. 

NOTE:
· SIGNAL SEARCH is not available when any input signal is projected. 

INSTALLATION
When installing the projector,  select the projection method according to the projector position. See "Projection method" on page 16. FRONT/DESK FRONT/CEILING REAR/DESK REAR/CEILING
Setting on a desk/floor and projecting from front Mounting in the ceiling and projecting from front Setting on a desk/floor and projecting from rear Mounting in the ceiling and projecting from rear

DIRECT POWER ON
You can switch the projector start up status for when the electric power is supplied. Press I H to select the required option. 
OFF ON Starts in the same mode as last use. Skips the standby mode and starts the projection. 

NOTE:
· If the projector is started from the projecting mode,  the POWER button pressing procedure is skippable. 

CONTROL PANEL
You can turn off the function of the control panel buttons on the projector body.  [. . . ] Attendez au moins 1 heure que la lampe et les composants contigus soient suffisamment froids. Préparer un tournevis cruciforme. Contacter un centre de service aprés-vente agréé pour acheter une Unité de la lampe (ET-LAB80) de rechange. En cas d'installation du projecteur au plafond,  ne jamais travailler directement dessous et éloigner le visage du projecteur. 

REMARQUE:
· Avant de remplacer la lampe,  la laisser refroidir pour éviter les risques de brûlures,  les dommages et autres dangers.  [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PANASONIC PT-L797PWUL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PANASONIC PT-L797PWUL will begin.