User manual PANASONIC PT-P1SDU

[. . . ] R LCD Projector Commercial Use Operating Instructions Model No. PT-P1SDU POWER INPUT MENU ENTER AUTO SETUP STD SHUTTER RETURN ENTER VOLUME ROTATE Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ 0184 ENGLISH Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product can be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. [. . . ] Set to "PHOTO" when projecting photographs. When set to "AUTO", the picture mode will be automatically switched to the best mode. DETAILED SETUP You can adjust the picture quality of the projected images in detail. Press the ENTER button to display the "DETAILED SETUP" menu. COLOR The color is too pale: F button The color is too deep: G button TINT [S-VIDEO/VIDEO (NTSC/NTSC 4. 43)/YPBPR only] This adjusts the flesh tones in the picture. The flesh tones are greenish: I button The flesh tones are reddish: H button DETAILED SETUP CONTRAST 32 BRIGHTNESS 32 COLOR ADJUSTMENT SELECT ENTER RETRN CONTRAST This adjusts the contrast of the picture. (Adjust the "BRIGHTNESS" setting first if required before adjusting the "CONTRAST" setting. ) The picture is bright: I button The picture is dark: H button PICTURE ADJUSTMENT PICTURE MODE STANDARD DAYLIGHTVIEW AUTO DETAILED SETUP SELECT ADJ RETRN DAYLIGHTVIEW This adjusts the vividness of the projected images when the projector is used under bright lighting. PICTURE MODE When an S-VIDEO/VIDEO/YPBPR signal is being input PICTURE MODE NATURAL [ BRIGHTNESS Adjustments and settings ENGLISH-45 This adjusts the darker areas (black areas) in the picture. Black areas are too light: I button Dark areas are too solid: H button DAYLIGHTVIEW AUTO [ OFF AUTO The vividness of the projected images will be adjusted according to the lighting condition of the room. OFF "DAYLIGHTVIEW" is disabled. NOTE: B "AUTO" may not function correctly if any objects are placed on the projector. B "DAYLIGHTVIEW" will be disabled when "FRONT/REAR" in the "OTHER SETUP" menu is set to "REAR". STANDARD [ COLOR ADJUSTMENT (S-VIDEO/VIDEO/YPBPR only) You can adjust the color of the projected image. Press the ENTER button to display the adjustment screen. DYNAMIC When a PC signal is being input PICTURE MODE DYNAMIC [ NATURAL [ STANDARD When an SD signal is being input PICTURE MODE AUTO [ PHOTO [ STANDARD [ COLOR 32 TINT 32 DYNAMIC 44-ENGLISH Adjusting the position Press the F or G button on the remote control unit to select an item, and then press the I or H button to change the setting. For items without any selective setting, press the ENTER button. The next screen for the item will then be displayed. For items with bar scales, press the ENTER button or the I or H button to display the adjustment screen, and then press the I or H button to make the adjustment. KEYSTONE ADJUSTMENT 0 reset if the tilt is different from the last time you used the projector. when you change the setup place), correct the keystone distortion again. S4:3 The size of the input signal is compressed to 75% and projected. (This is useful for projecting a picture with a 4:3 aspect ratio onto a 16:9 screen. ) ASPECT Picture condition Operation Press the F or Hbutton. NOTE: B Vertical keystone distortion can be corrected to ±30° of the angle of tilt by combining automatic correction and manual correction. However, the greater the correction amount, the more the picture quality will deteriorate, and the harder it will become to achieve a good level of focus. To obtain the best picture quality, set up the projector and screen in such a way that the amount of keystone correction required is as minimal as possible. B The picture size will also change when correction of keystone distortion is carried out. B The ratio of length and width of an image may become incorrect depending on the amount of the keystone correction. B Keystone distortion of the onscreen display will not be corrected. B If you correct the keystone distortion manually, the amount of correction will be stored by the projector even after the power is turned off. [. . . ] Ensuite, tenir la poignée du bloc de lampe et tirer progressivement le bloc de lampe hors du projecteur. Poignée Notes sur le remplacement du bloc de lampe B La lampe produisant la lumière est en verre; il ne faut donc pas la laisser tomber ou la cogner contre des objets rigides, car elle risquerait d'éclater. Faire bien attention lorsqu'on manipule la lampe. B Jeter la lampe usagée de la même manière qu'une lampe fluorescente. [. . . ]