User manual PANASONIC PV-M2057

[. . . ] To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://www. panasonic. co. jp/global/ Trademark Credits VGA is a trademark of International Business Machines Corporation. Macintosh is a registered trademark of Apple Computer, USA. [. . . ] Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected. · · · · · If the cabinet becomes dirty, wipe it with a soft, dry cloth. If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth. Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result. Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC. 6 Accessories Accessories Supply Check that you have the accessories and items shown Operating Instruction book Remote Control Transmitter EUR646525 INPUT SURROUND Batteries for the Remote Control Transmitter (2 × R6 Size) Guarantee Card VOL N R PICTURE SOUND SET UP PICTURE POS. /SIZE ASPECT PC OFF TIMER PLASMA DISPLAY AC cord Fixing bands TMME187 × 2 Ferrite core (small size) J0KF00000018 × 1 Ferrite core (large size) J0KG00000054 × 2 Optional Accessories · Speakers TY-SP42P5W-H (TH-42PHW5) TY-SP50P5W-H (TH-50PHW5) · Pedestal · Wall stand TY-ST10-H TY-ST42PW1 · Mobile stand TY-ST42PF3 · Wall-hanging bracket (vertical) TY-WK42PV1 · Wall-hanging bracket (angled) TY-WK42PR1 · Ceiling unit TY-CE42PS1 For assembling Full instructions are supplied with each optional accessory for use with this Plasma Display. 7 Remote Control Batteries Requires two R6 batteries. Install the batteries as shown in the battery compartment. (Polarity + or ­ must match the markings in the compartment. ) 3. Replace the cover and slide in reverse until the lock snaps. Two "R6" size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. Communication parameters Signal level Synchronization method Baud rate Parity Character length Stop bit Flow control RS-232C compliant Asynchronous 9600 bps None 8 bits 1 bit RS-232C Conversion cable D-sub 9-pin female Details RXD 2 TXD 3 GND 5 Non use 46 7 8 1·9 Shorted NC Basic format for control data The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX End (03h) Command Command PON POF AVL AMT IIS Parameter None None Control details Power ON Power OFF Volume 00 - 63 Audio mute OFF Audio mute ON Input select (toggle) AV Mode Component / RGB mode (processed as a Y/PB/PR or RGB signals as set by this unit) PC Mode Screen mode select (toggle) 4:3 Zoom 16 : 9 Just Panasonic Auto ** Start (02h) Colon Parameter(s) (1 - 5 bytes) 3-character command (3bytes) 0 1 None VID YP1 RG1 None NORM ZOOM FULL JUST SELF Notes: (1) If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. (2) If an incorrect command is sent by mistake, this unit will send an "ER401" command back to the computer. DAM With the power off, this display responds to PON command only. 15 Basic Controls R - STANDBY G POWER ON TH-50PHW5 INPUT -- VOL + Main Power On/Off Switch Power Indicator The Power Indicator will light. Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet. ) Stand-by . . . . Green INPUT button (AV(S Video), Component/RGB and PC Mode Selection) Press the "INPUT" button to select AV (S Video), Component/RGB and PC input signal modes sequentially. (see page 19) · · · Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. Stand-by (ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 18). Press this button to turn the Plasma Display On, from Stanby mode. [. . . ] ("Signal [AV]" menu is displayed. ) Press to select 3:2 Pulldown. Press to set On/Off. Component/RGB-in select RGB Signal Screensaver OSD Language English (UK) Press Signal (ACTION) button [ AV ] On Auto Off 4:3 Note: When On, this setting only affects the following signal input: · NTSC signal input during "AV(S Video)" input signal mode. · 525i(480i) signal input during "Component" input signal mode. R 3D Y/C Filter (NTSC) Colour system 3:2 Pulldown Panasonic Auto (4:3 ) Signal [ Component ] Off Press to exit from adjust mode. 3:2 Pulldown 33 Setup for input signals Sync Select Signal from the "Setup" menu during RGB or PC input signal mode. Setup Component/RGB-in select RGB Signal Screensaver OSD Language English (UK) Press to adjust. Press (ACTION) button Signal Sync R [ RGB ] H&V H-Freq. 31. 5 kHz 60. 0 Hz Press to exit from adjust mode. Signal Sync Setting RGB sync signal: Confirm that the input is set to RGB input (this setting is valid only for RGB input). [. . . ]