User manual PANASONIC PV-M2069W

[. . . ] Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING : To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain or moisture. Do not place containers with water (flower vase, cups, cosmetics, etc. ) above the set. [. . . ] · If adjusting the PICTURE V-POS/V-SIZE in Panasonic AUTO with FULL mode, the adjustment is not memorized. When exiting the mode, the screen will return to a former adjustment. · Panasonic AUTO can not be selected while TY-FB9BD (optional BNC Dual Video Terminal Board) is installed. 4 3 16 Panasonic AUTO 9 Panasonic AUTO For an elongated image 4 3 Image is expanded Changes in accordance with the Panasonic AUTO mode setting (see page 33). For a 4:3 image Note: Do not allow the picture to be displayed in NORMAL mode for an extended period, as this can cause a permanent after-image to remain on the Plasma Display Panel. 18 Adjusting POS. Press to select H-POS / H-SIZE / V-POS / V-SIZE / CLOCK PHASE. 3 Press to adjust POS. /SIZE. During "VIDEO (S VIDEO)", "COMPONENT" and "DVI" input signal. 4 Press to exit from adjust mode. POS. /SIZE NORMALIZE NORMAL Notes: · Adjustment details are memorized separately for different input signal formats (Adjustments for component signals are memorized for 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p each, and RGB/PC/DVI signals are memorized for each frequency. ) · If a "Cue" or "Rew" signal from a VCR or DVD player is received, the picture position will shift up or down. This picture position movement cannot be controlled by the POS. · If adjusting the PICTURE V-POS / V-SIZE in Panasonic AUTO with FULL mode, the adjustment is not memorized. When exiting the mode, the screen will return to a former adjustment. H-POS Adjust the horizontal position. H-POS H-SIZE V-POS V-SIZE 0 0 0 0 During "RGB / PC" input signal. POS. /SIZE NORMALIZE NORMAL H-POS H-SIZE V-POS V-SIZE CLOCK PHASE 0 0 0 0 0 H-SIZE Adjust the horizontal size. V-POS Adjust the vertical position. V-SIZE Adjust the vertical size. CLOCK PHASE (RGB/PC in mode) Eliminate the flickering and distortion. Helpful Hint ( / NORMALIZE Normalization) While the POS. · In 2 screen display, the same input mode cannot be selected for the main picture and sub picture. · The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of the pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals displayed on the main picture and depending on the 2-picture display mode. · Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail. · Computer screen picture is displayed in a simplified format, and it may not be possible to discern details on them satisfactorily. · Following combinations of two analog signals cannot be displayed simultaneously. Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB) · Refer to each board's operating instruction for DVI, SDI, HDMI's corresponding signals. 21 PICTURE Adjustments 1 2 Press to display the PICTURE menu. Press to select the menu to adjust. Select the desired level by looking at the picture behind the menu. PICTURE NORMALIZE NORMAL 1/2 STANDARD 25 0 0 0 3 PICTURE MENU PICTURE BRIGHTNESS COLOR TINT SHARPNESS Press the left or right button to switch between modes. STANDARD CINEMA DYNAMIC STANDARD For viewing in standard (evening lighting) environments. This menu selects the normal levels of BRIGHTNESS and PICTURE. DYNAMIC For viewing in brighter environments. [. . . ] The owner must produce the product purchase receipt or other satisfactory evidence of date of original purchase. This warranty does not apply to external appearance items, such as handles, knobs, safety windows, etc. This warranty does not apply to any part, or parts, of the product, installed, altered, repaired or misused in any way that, in the opinion of PCI, affects the reliability of or detracts from the performance of the product. For products requiring routine preventive maintenance, that maintenance must be performed in order to maintain warranty coverage. [. . . ]