User manual PANASONIC PV-M2776

[. . . ] Visit our Panasonic Web Site http://panasonic. net Table of Contents Important Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · You can change the level of each function (Contrast, Brightness, Colour, Tint, Sharpness) for each Picture Mode. · The setting details for normal, dynamic and cinema respectively are memorized separately for each input terminal. · The "Tint" setting can be adjusted for NTSC signal only during "AV (S Video)" input signal. · In Contrast, there is not a noticeable change even when contrast is increased with a bright picture or reduced with a dark picture. Advanced settings (For TH-42PS10RK/S) Advanced settings Normalise Normal Item 0 0 0 0 0 0 2. 2 Off Effect Less More Details Adjusts the dark shades of the image in gradation. Adjustment of parts which are extremely bright and hard to see. (This cannot be adjusted when the input signal is Digital. ) Adjusts the white balance for light red areas. Adjusts the white balance for light blue areas. Adjusts the white balance for dark red areas. Adjusts the white balance for dark blue areas. S Curve 2. 0 2. 2 2. 5 Black extension Input level W/B High R W/B High B W/B Low R W/B Low B Gamma AGC Black extension Input level W/B High R W/B High B W/B Low R W/B Low B Gamma AGC Less More Less More Less More Less More Less More Down Up Off On Increases the brightness of dark signal automatically. Notes: · Carry out "W/B" adjustment as follows. Adjust the white balance of the bright sections using the "W/B High R" and "W/B High B" settings. The operation guide will be displayed. Exit 1 During Digital Zoom, only the following buttons can be operated. [Remote control] POSITION / ACTION button INPUT MENU -/ VOL [Unit] +/ ENTER/ VOL button VOL button MUTE button SURROUND button OFF TIMER button 2 Select the area of the image to be enlarged. Press on the enlargement location to select. The cursor will move. Exit 2 3 Select the magnification required for the enlarged display. Each time this is pressed, the magnification factor changes. This is shown in the image being displayed. ×1 ×2 ×3 ×4 4 Return to normal display (quit Digital Zoom). Press to exit from the Digital Zoom. Notes: · When power goes OFF (including "Off Timer" operation), Digital Zoom terminates. · The Digital Zoom function cannot be selected while in the following operation state: "Multi-viewer" (Picture in Picture, Picture out Picture, Picture and Picture) operation. (see page 20) · While Digital Zoom is in operation, "Adjusting Pos. / Size" cannot be used. 26 PRESENT TIME Setup / Set up TIMER The timer can switch the Plasma Display On or Off. [. . . ] Check The screen will darken slightly when photos, still images of a computer or other pictures with minimal movements are shown for an extended period. This is done to reduce image retention on the screen and the shortening of the screen's service life: It is normal and not indicative of malfunctioning. The unit digitally processes the various signals in order to reproduce esthetically pleasing images. As such, it sometimes takes a few moments for the picture to appear when the power has been turned on, when the input has been switched or when the images for the main picture and sub picture on the two screens are swapped. [. . . ]