User manual PANASONIC PV-Q130W

[. . . ] Do not place liquid containers (flower vase, cups, cosmetics, etc. ) above the set (including on shelves above, etc. ). WARNING : 1) To prevent electric shock, do not remove cover. Refer servicing to qualified service personnel. 2) Do not remove the grounding pin on the power plug. [. . . ] Press to select "DST" (Daylight saving). CH Manual Press to select "On" or "Off". - VOL OK VOL+ CH Date 4 / 1 / 2005 Time 9 : 43 AM Time zone EST DST On Auto program Auto program is not available while the CableCARDTM is inserted. You can scan All (Analog and Digital) channels. If needed, follow the menus and procedures displayed on-screen for setting up the features. You can also adjust the settings in Setup menu. 1 CH Press to select "ANT In". Press to select "Cable" or "Antenna". VOL+ - VOL OK Auto program ANT In Cable Mode All Start scan CH 2 CH Press to select "Mode". Press to select "All" or "Analog ". VOL+ Auto program ANT In Cable Mode Start scan All - VOL OK CH 3 CH Press to select "Start scan". Channels available for reception will be set automatically. Now scanning analog channel . . . Progress Auto program ANT In Cable Mode Start scan All - VOL OK VOL+ CH To exit the menu screen Press EXIT 19 Watching TV programs 1 POWER TV Press to operate the TV set with the remote control. SAP LIGHT TV DTV TV/VIDEO VCR RCVR DVD DBS/CBL SLEEP 2 POWER Press to turn the TV on. AUX EXIT PECT AS FAVORIT E MU T E CH RE 3 CH - VOL MENU OK VOL+ Press to select desired channel. · You can also use the direct program number selection buttons and PROG­button (see page 17). VOL+ CH RETURN LL CA - VOL OK CH 4 - VOL CH Select the desired volume level. VOL+ OK 1 4 7 R-TUNE 2 5 8 0 3 6 9 PROG CH REW PLAY FF PAUSE STOP REC TV/VCR DVD/VCR CH OPEN/CLOSE Notes: · The channel number and volume level remain the same even after the TV is turned off. · Power consumption and howling sound can be reduced if the volume level is lowered. TV 20 Aspect Controls Let you choose the aspect depending on the format of the received signal and your preference. PECT AS POWER Press to change the aspect mode. SAP LIGHT Note: The available aspect modes depend on the receiving signal. TV DTV TV/VIDEO VCR RCVR DVD DBS/CBL SLEEP AUX EXIT · 480i, 480p (4:3), 480p (16:9) · 1080i / 720p : 4:3, Full, Just or Zoom : 16:9 only PECT AS MU T FAVORIT E E CH RE LL CA - VOL MENU OK VOL+ CH RETURN Mode Picture 4 4:3 Explanation Displays a 4:3 picture at its standard 4:3 size with gray side bars. (It may create an after-image on screen if displayed for a prolonged period of time. ) 4:3 3 4 Zoom 16 3 9 Zoom Expands a 4:3 picture uniformly (width and height) to full screen width and then repositions the picture vertically. This feature also affects Color Temp setting. mode". CH - VOL OK VOL+ CH Press to select the picture mode. · Vivid (default) : Provides enhanced picture contrast and sharpness for viewing in a well-lit room. · Standard : Recommended for normal viewing conditions with subdued room lighting. · Cinema : For watching movies in a darkened room. It provides a soft, film-like picture. Note: Each mode has its own picture settings (Picture, Brightness, Color, Tint and Sharpness). 24 Sub-Menu Navigation Zoom Adjust Adjust the Zoom position. Press to display the Zoom Adjust screen. Press to adjust V-Position. CH Picture 1/2 Normal Pic. mode Picture Brightness Color Tint Sharpness No Standard +30 0 0 0 +10 Picture 2/2 Color Temp Color Mng. Zoom Adjust Other Adjust Cool Off CH - VOL OK VOL+ CH - VOL OK VOL+ CH Note: To return to the default setting, press the "OK" button. Press to adjust Size. · V-Position : Adjust the vertical position. [. . . ] · Check if the power cord is plugged into the wall outlet. · Adjust Brightness and Audio controls. · Program the remote control code. · Check the second video source operation. [. . . ]