User manual PANASONIC PV-V402

[. . . ] Location of Controls Multi Function Display Power Indicator Lights up when power is on. Timer Indicator Lights up when the VCR is set for a Timer Recording, or when One Touch Recording (OTR) is used. Flashes when a Timer Recording is set, but a tape has not been inserted into the VCR. Spanish Quick Use Guide/ Guía para rápida consulta CONEXIONES/CONFIGURACIÓN INICIAL (READY TO PLAY) Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA. La videograbadora iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA. Spanish Quick Use Guide/ Guía para rápida consulta OPERACIONES BÁSICAS PARA LA REPRODUCCIÓN Spanish Quick Use Guide/ Guía para rápida consulta ANTES DE AL SERVICIO SOPORTE TÉCNICO Verifique los siguientes puntos una y otra ves si esta teniendo problemas con su VCR. (BO : Haga referencia en la instruciones de funcionamiento [Operaciones Básicas]) (AO : Haga referecncia el la instruciones de funcionamiento [Operaciones Avanzadas]) Limited Warranty PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA One Panasonic Way Secaucus, New Jersey 07094 PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC. , Ave. 9. 5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 · Limited Warranty · Guía para rápida consulta (Spanish Quick Use Guide) · Guía para rápida consulta (Spanish Quick Use Guide) · Location of Controls (Multi Function Display, Rear View of the VCR) 1 Inserte una cassette, 2 Presione PLAY para reproducir el · la alimentación del VCR se activa. [. . . ] You may moisten cloth with nonabrasive, antistatic cleaner/ polisher. Caution: Alcohol and various solvents could damage finish. For DSS/Cable Box VCR TV 1 Connect your cable box's TV OUT jack to the VCR's IN FROM ANT. 2 Connect VCR's OUT TO TV jack to TV's ANT. IN jack with included RF Cable accessory. Initial Setup (Ready to Play) Press PROG to end programming. VCR IN FROM ANT. Cable TV Converter Box 5 Press STOP to stop recording. One Touch Recording (record in progress) Press REC repeatedly to set length as follows: 30 min. The VCR shuts off at the length set. 3 COMMERCIAL SKIP/ ZERO SEARCH (Starts COMMERCIAL SKIP/ Zero Search) ACTION (Displays menu) REWIND/SEARCH (Rewinds tape/ reverse visual search) STOP (Stops tape) TIMER PROG. L I ST DT START STOP CH SPD 13 2 : 00 P 3 : 20P 02 SLP -- -- : -- -- : --- --- --- -- : -- -- : --- -- : -- -- : --- -CANCEL : ADD / DLT SELECT : SET : EXIT : PROG OUT TO TV 1 IN from ANT. /CABLE To Enter More Programs to select and Press press to set an unused program. Or, press PROG to exit. RECORD (Records a program, etc. ) Remote keys PLAY, STOP, REW, and FF function as operation keys when menus are displayed. VHF/UHF 2 4 Press POWER off to set the timer recording. ("TIMER" lights on Multi Function Display. ) Review, Replace, or Clear Program (Recording is not in progress) Cancel a Timer Recording (Recording is in progress) Press POWER and then STOP within 10 seconds to cancel the Timer Recording. (The TIMER indicator goes out on Multi Function Display. ) TAPE POSITION (Locates tape position) Specifications To order accessories, call toll free 1-800-332-5368. Power Source: 120 V AC, 60 Hz Power Consumption:Power On Approx. 18 W Still (Freeze) Picture Press PAUSE/SLOW. Press PLAY to release. Record one station, watch another Press VCR/TV ("VCR" goes out on Multi Function Display), select channels on TV (recording continues). COUNTER RESET (Resets counter to zero) PROGRAM (Displays Timer Program screen) Loading the Batteries Power Off Video Signal: Video Recording System: Audio Track: Tuner: Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A ~ I (14 ~ 22) Superband J ~ W (23 ~ 36) Hyperband AA ~ EEE (37 ~ 64) Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01) Ultraband 65 ~ 94, 100 ~ 125 Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F) Operating Humidity: 10 % ~ 75 % Weight: 2. 5 kg (6. 0 lbs). Dimensions: 360 (W) x 93 (H) x 242 (D) mm 14-3/16" (W) x 3-11/16" (H) x 9-9/16" (D) inch Approx. 2. 5 W EIA Standard NTSC color 4 rotary heads helical scanning system 1 track (Normal) 1 Turn TV on and tune to channel 3. 2 Plug VCR Power Cord into AC wall outlet. VCR comes on and auto channel and clock set starts. · If screen below does not appear, check VCR - TV connection and, if TV is tuned to channel 3, try switching it to channel 4. · To change VCR's output channel, please refer to "VCR's Output Channel" in Advanced Operations book (p. 12). 3 Settings are made automatically. When setup is done, this screen appears. VCR CLOCK CHANNEL Frame by Frame Picture Press PAUSE/SLOW in Still mode. Slow Motion Picture Hold down PAUSE/SLOW in Still mode. Notes · These features work best in SP or SLP mode. · To reduce picture noise, see "Manual Tracking Control" on p. [. . . ] 03 Zenith . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 Magnavox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05 Sylvania . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05 Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]