User manual PANASONIC RCDC1EB

[. . . ] Operating Instructions Clock Radio Model No. RC-DC1 Note: "EB" on the packaging indicates the United Kingdom. EB RQTX1210-1B Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions thoroughly before connecting, operating or adjusting this product. Keep this manual for future reference. CAUTION! · DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS. [. . . ] Press [2/­, ADJ] or [+/6, ADJ] to select the day. Repeat steps 2 and 3 to set the hour and minute. Example: 3 4 To change the clock display In clock mode, press and hold [+, VOL] and [­, VOL] at the same time for 2 seconds to select between a 12-hour or 24-hour display. For 12-hour display: AM : "PM" is not displayed. PM : "PM" is displayed. 10 Daylight saving time (summer time) In clock mode, press and hold [SLEEP] to activate or cancel daylight saving time (summer time) function. "DST" is displayed when the function is activated. Using an iPod or iPhone 1 Pull out the iPod or iPhone support. Adjust the support according to the height of your iPod or iPhone. iPod (not included) Synchronising clock with iPod or iPhone time This function allows you to set the clock's time to be the same time as your iPod or iPhone's time (Z page 7, "Compatible iPod or iPhone"). Press [TIME SYNC] while an iPod or iPhone is docked unto the main unit. Note: · Exact synchronisation of an iPod or iPhone with the main unit is not possible. There could be a difference of up to 59 seconds between them. · Compatibility depends on the software version of your iPod or iPhone. Gently pull out the iPod or iPhone support. iPod classic iPhone iPod touch iPod nano 2 Connecting an iPod or iPhone. Hold the main unit when connecting or disconnecting the iPod or iPhone. (Continued on next page) 11 RQTX1210 Note: When docking an iPod touch or iPhone for the first time, a message will be displayed on your iPod touch or iPhone if the Memory Loader application has not been installed (Z page 15). Charging an iPod or iPhone The iPod or iPhone charges automatically when connected to the main unit. · See iPod or iPhone display to check its charging status. · If the iPod or iPhone is not being used for an extended period of time after charging has completed, disconnect it from the main unit, as the battery will be depleted naturally. (Once fully charged, additional charging will not occur. ) Using the radio Manual tuning Playing an iPod or iPhone 1 2 3 4 5 Place an iPod or iPhone in the dock and turn it on. Press [SOURCE] to select "IPOD". Press [4/9] once to start music playback from the iPod or iPhone. Press [SLEEP] again to select your desired time (in minutes). OFF (default) ] 30 ] 60 ] 90 ] 120 6 7 Press [ALARM 1] or [ALARM 2] to confirm. Press [2/­, ADJ] or [+/6, ADJ] to select the desired alarm mode: "IPOD", "RADIO" or "BUZZER". Note: Press [SLEEP] once to check the remaining time. (Continued on next page) 13 RQTX1210 8 Press [ALARM 1] or [ALARM 2] to confirm. "IPOD" selection: Continue with steps 9 and 10. [. . . ] If you are in doubt about some of the check points, or if the solutions indicated do not solve the problem, consult your dealer for instructions. Clock Clock cannot be synchronised to iPod or iPhone's time. · Make sure the iPod or iPhone is securely connected and turned on (Z page 11). · Update your iPod or iPhone with the latest software. [. . . ]