User manual PANASONIC RP-BT10

[. . . ] Operating Instructions Digital Wireless Earphones Model No. RP-BT10 Dear Customer Thank you for purchasing this product. Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference. P RQT8993-1P IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 5) Do not use this apparatus near water. [. . . ] Avoid listening for prolonged periods of time to prevent hearing damage. (Refer to page 28. ) Concerning the ear pads RQT8993 Your earphones are fitted with M size ear pads at the time of their purchase. If you feel that they are too small or too large for your ears, replace them with the S or L size pads. 14 Listening to music on your iPod® Setting the pair As soon as the receiver and transmitter power are turned on, the pair setting is performed automatically. Connect the transmitter to the dock connector on the bottom of the iPod®. ·The iPod®'s power is now automatically turned on. Press and hold the MIC button on the receiver for 2 seconds. · The receiver's power is now turned on, and the lamp (red) blinks slowly. Press and hold the Transmitter button on the transmitter for 2 seconds. · The transmitter's lamp (red) starts blinking rapidly, and when the pair setting is completed, the lamps (blue) on the transmitter and receiver start blinking slowly to indicate that the pair setting has been completed. Note: · To establish pairing again after pairing has been released or the transmitter's power was turned off, press and hold the Transmitter button on the transmitter for 2 seconds. The pair setting is restored. RQT8993 15 Listening to music on your iPod® Operating the receiver As soon as the pairing has been set, the iPod® can be operated by remote control. : Each time this is pressed, the mode is switched. Next/Fast-forward : Press this once to skip to the next track; Press and hold it down to fast-forward. Previous/Rewind : Press this once to return to the beginning of the previous track; Press and hold it down to rewind. Volume (up) : Use this to adjust the volume level in 16 steps. Volume (down) : Use this to adjust the volume level in 16 steps. · Some operations may not be supported depending on the player you are using. · When you pause operation using the receiver, the iPod® screen flashes approximately every 20 seconds. This is to prevent the power from automatically turning off, and it is not a malfunction. · The earphone volume depends on the receiver side, so changing the iPod® volume does not change the earphone volume. · Even if you change the volume with the receiver, the iPod® volume display does not change. RQT8993 Play/pause 16 Winding up an operation session Press and hold the MIC button on the receiver for 6 seconds. The receiver's power is turned off, the pairing setting is released, and the lamp goes off. · The iPod®'s power turns off automatically. Lamp OFF If you also establish pairing with a Bluetooth cellphone, you can receive calls to your Bluetooth cellphone while listening to music on your iPod®. RQT8993 17 Talking on your cellphone Registering the device pair In order to establish the wireless connection between the receiver and Bluetooth cellphone, the receiver and cellphone pair must be registered. · Operations involving the receiver Press and hold the MIC button on the receiver for 2 seconds. The receiver's power is turned on, and its lamp (red) starts blinking slowly. Press and hold the [­] button on the receiver for 6 seconds. The lamp (red) starts blinking rapidly. Caution: While the lamp (red) blinks rapidly (for about 60 seconds), register the pairing of the receiver and Bluetooth cellphone. · Operations involving the Bluetooth cellphone if the lamp (red) starts blinking Using your cellphone, conduct a Bluetooth device search. Caution: · A list of detected devices is displayed on the cellphone screen, and "RP-BT10R Panasonic" is displayed for the receiver. If "RP-BT10R Panasonic" is not displayed, repeat the procedure from step · If you are requested to input the pass key, input "0000. " RQT8993 . Notes: 18 · For further details on conducting the Bluetooth device search, refer to the operating instructions of your cellphone. · Once the pairing has been registered, it need not be registered again. · It may not be possible to register the pairing with some cellphones because they use a different data transfer format. Setting the pair In order to establish the wireless connection between the receiver and Bluetooth cellphone, the receiver and cellphone pair must first be registered. Before operating the units, check the following points. · Has the pairing of the receiver and cellphone you are about to use been registered?(Refer to page 18. ) Press and hold the MIC button on the receiver for 2 seconds. The receiver's power is turned on, and its lamp (red) starts blinking slowly. Establish a "hands-free" connection by performing the Bluetooth connection operation on your cellphone. · When the pair setting is completed, the receiver's lamp (blue) starts blinking slowly. [. . . ] THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER "LIMITED WARRANTY COVERAGE". THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING WITHOUT LIMITATION, LOSS OF GOODWILL, PROFITS OR REVENUE, LOSS OF USE OF THIS PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF SUBSTITUTE EQUIPMENT, DOWNTIME COSTS, OR CLAIMS OF ANY PARTY DEALING WITH BUYER FOR SUCH DAMAGES. (As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, travel to and from the servicer. The items listed are not exclusive, but are for illustration only. ) ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY. [. . . ]