User manual PANASONIC RP-HDA100

[. . . ] 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of polarized or grounding-type plug. [. . . ] Lamp: This indicates the status of the device. (Refer to page 23. ) DC IN socket: Connect the accessory AC adaptor or USB cable here. (Be sure to use the AC adaptor or USB cables that have been provided as an accessory. Trouble or malfunctioning may result if a product such as one with different plug polarities is used instead. Reset switch: (Refer to page 25. ) AUDIO OUT (line out) connector: Connect the earphones with the 3. 5 mm plug to this connector. Microphone: The microphone used when talking on the phone is built-in. MIC button: Use this to turn the power on or off, start talking when receiving an incoming call or end talking to terminate the call, set the pairing, etc. Stereo earphones (L / R) 12 RQT8993 Preparations (prior to use) Charging (only the receiver) The unit (receiver) contains a rechargeable nickel-hydrogen battery. Recharge this battery prior to use. When using the AC adaptor to recharge the battery When connecting the USB cable to a PC to recharge the battery Connect one end of the USB cable to the receiver and the other end to the PC. The receiver's lamp (purple) lights up. When charging is completed, the lamp goes off. (Refer to page 18. ) Press and hold the MIC button on the receiver for 2 seconds. The receiver's power is turned on, and its lamp (red) starts blinking slowly. Establish a "hands-free" connection by performing the Bluetooth connection operation on your cellphone. · When the pair setting is completed, the receiver's lamp (blue) starts blinking slowly. · To establish pairing again after pairing has been released or the receiver's power was turned off, press the MIC button on the receiver once, then check the connection with the cellphone. Note: · For further details on the Bluetooth connection operation, refer to the operating instructions of your cellphone. RQT8993 Hands -free 19 Talking on your cellphone Talking on the phone Receiving incoming calls You will hear the incoming call tone when someone calls the number of your cellphone. MIC - To talk to the other party, Press the MIC button on the receiver. - To switch the call to your cellphone, Press and hold the MIC button on the receiver for 2 seconds after the call has been connected. - To refuse the call, Press and hold the MIC button on the receiver for 2 seconds during the call tone. Hanging up Press the MIC button on the receiver. Notes: · If you receive a call while music is playing on the iPod®, the iPod® music will be temporarily suspended, and you will hear the incoming call tone. · When the call is terminated, the iPod® music will resume. Adjusting the call volume The call volume can be adjusted by pressing the [+] and [­] buttons. Notes: · The call volume cannot be adjusted during call standby. · You can select separate settings for the call volume level and music play level. RQT8993 Winding up an operation session Disconnect the Bluetooth connection using your cellphone. Note: · For further details on disconnecting the Bluetooth connection, refer to the operating instructions of your cellphone. 20 Press and hold the MIC button on the receiver for 6 seconds. The receiver's power is turned off, and its lamp (red) goes off. Listening to music on your cellphone Setting the pair In order to establish the wireless connection between the receiver and Bluetooth cellphone, the receiver and cellphone pair must first be registered. Before operating the units, check the following points. · Has the pairing of the receiver and cellphone you are about to use been registered?(Refer to page 18. ) Press and hold the MIC button on the receiver for 2 seconds. The receiver's power is turned on, and its lamp (red) starts blinking slowly. Establish the "audio" connection by performing the Bluetooth connection operation on your cellphone. [. . . ] Once you have established a comfortable sound level: · Leave it there. Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way Secaucus, New Jersey 07094 FOR U. S. A. Panasonic Puerto Rico, Inc. 9. 5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Panasonic / Technics Accessory Limited Warranty Limited Warranty Coverage If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or Panasonic Puerto Rico, Inc. (collectively referred to as "the warrantor") will, for the length of the period as follows, which starts with the date of original purchase ("warranty period"), replace it with a new or a refurbished product. Product Parts Service Carry-in or Mail-in not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, rental use of the product, serviced by anyone other than a Factory ServiCenter or other Authorized Sevicer, or damage that is attributable to acts of Gods. [. . . ]