User manual PANASONIC RX-C60

[. . . ] · The function selector switch does not separate entire unit from mains even if in "TAPE/ OPR OFF " position. A Connect the speaker cords terminals and Connect only positive (red) wires to positive negative (black) wires to negative terminals. B Attaching the speakers Align the speaker with the main unit as shown in the figure, interlock the grooves and press down. C Detaching the speakers Unlock the speaker release levers by pulling them in direction shown as illustrated, and slide each speaker up. Caution · Use the speakers only with the recommended system. Failure to do so may lead to damage to the amplifier and/or the speakers, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if you experience a sudden change in performance. · Do not attach these speakers to walls or ceilings. 4 RQT7611 Power supply A AC power supply cord 1 VOLT ADJ 220240V 220240V B Batteries C Car battery cord 110127V 110127V 110-127V 220-240V R20/LR20 (D, UM-1) 2 5 6 8 3 1 4 7 AC IN ~ 2 To household AC outlet DC IN (12-13. 2V) 2 1 a A AC power supply cord Set the voltage. [. . . ] Replace the batteries when "OPERATION/BATT" goes dim during play. To prevent damage to the batteries and electrolyte leakage, heed the following points. · Do not use rechargeable type batteries. · Align the and polarities properly when inserting the batteries. · Do not mix different types or makes of batteries or old and new batteries. · Remove batteries if you do not plan to use the unit for a long time. If electrolyte leaks from the batteries, consult your dealer. Wash thoroughly with water if electrolyte comes in contact with any part of your body. Removal Insert your finger into the slot ( out the batteries. ) at the bottom of the unit and push C Car battery cord Insert the plug into the DC Input Jack. Plug the other end into the cigarette lighter socket in your car. 5 RQT7611 The radio A To improve reception 1 SELECTOR CD/ LINE IN RADIO TAPE/ 2 BAND SW1 SW2 FM MW 3 TUNING FM OPERATION/BATT MW/SW1 EDIT/FM MODE/BP HIGH/ STEREO/II NORMAL/ STEREO/II MIC/ MONO/I FINE TUNING L H SW1/SW2 Follow steps 1 to 3. In step 1: "OPERATION/BATT" lights while the radio is on. In step 2: Select FM, MW, SW1 or SW2. To turn off the radio Set [SELECTOR] to "TAPE/ OPR OFF ". A To improve reception FM: Raise and extend the whip antenna. To resume recording, press [ PAUSE] again. Recording tips · Changes to volume and tone will not affect the recording. · Wind up the leader tape before recording. · When recording MW, set [EDIT/FM MODE/BP] to the position where there is less noise. · Use the AC power supply cord or insert fresh batteries. · When erasing recorded sound, Insert the tape in Deck 1. Set [SELECTOR] to "TAPE/ OPR OFF ". Set [EDIT/FM MODE/BP] to "HIGH" or "NORMAL" . Press [ REC]. A Erasure prevention Break out the tab. Cover the tab with adhesive tape when you want to use the tape for recording again. 8 RQT7611 Recording tape to tape 2 4 EDIT/FM MODE/BP 1 SELECTOR CD/ LINE IN RADIO TAPE/ 3 HIGH/ STEREO/II NORMAL/ STEREO/II MIC/ MONO/I 6 Use normal position/TYPE I tape only. 5 7 RX-C60 RX-CT60 Follow steps 1 to 7. In step 1: Set [SELECTOR] to "TAPE/ OPR OFF ". In step 2: Insert the tape inside with the side to be recorded facing out and close by hand. In step 3: Insert the tape inside with the side to be played facing out and close by hand. [. . . ] · Any changes made to the volume or sound quality during recording will not affect the recording. 9 RQT7611 Other functions A Recording from an externally connected CD player etc. B Recording through the C built-in microphone (MIC) Equalizer/ Headphones 2 SELECTOR CD/ LINE IN RADIO TAPE/ 1 CD player, etc. 2 MIC EDIT/FM MODE/BP HIGH/ STEREO/II NORMAL/ STEREO/II MIC/ MONO/I 1 SELECTOR CD/ LINE IN RADIO TAPE/ CLEAR MIN HEAVY SOFT VOCAL FLAT XBS MAX CD/LINE IN White (L) Red (R) Stereo connection cable a CD/LINE IN 43 A NORMAL HIGH 43 PHONES Recording from an externally connected CD player etc. Connect the CD player (External equipment). Start recording, then start the CD playback. · Turn off all equipment before making any connection. [. . . ]