User manual PANASONIC RX-D11

[. . . ] Portable Stereo CD System Operating Instructions Model No. RX-D11 RX-D10 The illustrations show RX-D11. Note: The "EB" indication shown on the packing case indicates United Kingdom. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. EB GN RQT5210-B Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Table of Contents Before use (Back of product) Before use Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press [BAND] to select "FM" or "AM". Press [3] or [4] to select the preset channel. Using preset scan B You can search for a station by listening to all preset channels for 8 seconds each. Preparation: Set [ ] to "TUNER". Do steps 1 to 2 above. Press and hold [­/g] or [f/+] until "PS" appears on the display. Preset scan starts. 4 Press [­/g] or [f/+] when you find the desired channel. Preset scan ends after searching through each preset channel once. To stop during the process, press [­/g] or [f/+]. RX-D11 only When using the remote control Press [3] or [4] for [­/g] or [f/+] described above. B 2 Indicates preset scan 3 8 RQT5210 Listening to radio broadcasts L 2 1 3 4 Listening to broadcast stations which have not been programmed (Manual tuning) Preparation: Set [ ] to "TUNER". 1 Press [BAND] to select "FM" or "AM". Every time you press the button: FM AM 2 3 4 Press [TUNE MODE] to clear the preset indicator. The unit is set to the manual tuning mode. Press [­/g] or [f/+] to tune in the station. Adjust the volume. 2 3 4 Automatic tuning: This is a simple way of tuning in stations that have not been preset. Keep [­/g] or [f/+] depressed, and release it when the frequency display starts to change. A station with good reception is automatically selected and the selection process then stops. To stop automatic tuning, press [­/g] or [f/+] again. g f Hint Automatic tuning may stop without a station having been tuned in when interference is encountered on neighbouring airwaves. In such a case, tune in a station by tapping [­/g] or [f/+]. g f Using auto scan RX-D11 only You can search for a station by listening to all tuned-in stations for 8 seconds each. Preparation: Set [ ] to "TUNER". (Only from the remote control) 2 3 1 MEMORY/ PGM Press [BAND] to select "FM" or "AM". Press [AUTO SCAN]. Auto scan starts. 1 2 Indicates auto scan Press [AUTO SCAN] when you find the desired station. Auto scan ends when it reaches the original frequency again. To stop during the process, press [AUTO SCAN]. To turn off the unit: Set [ ] to "TAPE/ ". If the tape is travelling, press [L/c STOP/EJECT] as well. Adjusting the antennas A For FM reception: Pull out the telescopic antenna and adjust its length and angle for optimum reception. For AM reception: Turn the unit in the direction which gives the best results. Reference Radio broadcasts may be hard to receive in a moving vehicle or in a building because the signal may be weakened. In such cases, use the unit near a window. 3 A FM AM When there is a lot of noise in an FM stereo broadcast Reduce the interference by setting the sound to monaural. [. . . ] Leave it for about an hour before attempting operation again. 10 14 While using the cassette deck No recording. High level of noise; poor sound quality. The lid cannot be closed when loading the tape. [. . . ]