User manual PANASONIC RX-ED50A

[. . . ] Portable Stereo CD System Operating Instructions 1 4 7 2 5 8 3 6 9 10 0 TPS PORTABLE STEREO CD SYSTEM RX-ED50 RX-ED50A Note: The " EB " indication shown on the packing case indicates United Kingdom. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. EB GN RQT5142-1MB Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. CLASS 1 LASER PRODUCT Before use (Back of product) Table of contents Before use Caution for AC mains lead . [. . . ] ·Tracks cannot be selected with the numbered buttons. ·You cannot skip to tracks already played. ·Search can be done within tracks only. 10 RQT5142 CDs Program play: Select up to 36 tracks to play in the order you choose Preparation: Press [ /CLEAR] to switch to CD mode. Enter the track number with the numbered buttons. Press [ PORTABLE STEREO CD SYSTEM ]. All the tracks are played in the selected order. The program remains intact even if play is stopped or the unit is turned off. "Cd-P" appears when play is stopped to indicate the contents are in the memory. To cancel Press [ /CLEAR] while stopped. "CLEAR" is displayed, all the tracks are cleared, and program mode is canceled. The mode is also canceled if the CD tray is opened. "FULL" is displayed If 36 tracks have been programmed. "-- --:-- --" is displayed If the total play time of the program exceeds 100 minutes. You can still program and play tracks. To check the contents of the program While stopped Press [ ] or [ ]. Each time one of the buttons is pressed, a track and its order in the program are displayed. Program play does not work when " " is displayed (press [PLAY MODE] to clear it) ( page 10). Search can be done within tracks only. 11 RQT5142 Compact disc operations For tracks numbered 10 and over, press [10] then the two digits. Repeat this step to program the tracks in the required order. The radio: manual tuning Preparation: (when using batteries) Press [ ]. Press [BAND ] to select FM or AM. (Unit comes on when using AC power. ) Each time the button is pressed AM FM Press [ , REW­TUNE/ to select a station. " ­FF] " is displayed during FM stereo broadcasts. Press [­, +VOLUME] to adjust the volume. Auto-tuning Press and hold [ , REW­TUNE/ ­FF] until the frequency starts changing rapidly. (Interference may also cause it to stop. Start auto-tuning again if this occurs. ) To stop auto-tuning Press [ , REW­TUNE/ ­FF]. Radio operations To improve reception FM: Change the length and position of the antenna. AM: Change the facing of the unit. Frequency ·AM reception is briefly interrupted if a tape deck is operated. ·To improve reception when using the unit in a building or vehicle use it near a window. If noise is excessive in FM Remote control only Press [FM MODE/BP] to display " ". FM AM This mode improves sound quality if reception is weak for some reason but broadcasts are heard in monaural (" " goes out). Press [FM MODE/BP] again to cancel the mode. 12 RQT5142 The radio: preset tuning Presetting radio stations Remote control only Tuning is simpler if you preset stations. You can preset 12 FM and 12 AM stations. Preparation: Tune to the station you want to preset Press [PROGRAM]. While " " is flashing Press the numbered buttons to enter the station into a channel (1 to 12). ·To enter channels 10, 11, and 12 Press 10, then the two digits. ·If " " stops flashing Press [PROGRAM] again. The station occupying a channel is erased if another station is preset in that channel. Selecting channels On the main unit Press [BAND ] to select FM or AM. Turn [ TIME/PRE. TUNE/CD] to select the channel. On the remote control Press [TUNER] to select FM or AM. Press the numbered buttons to select the channel (1 to 12) the station is in. [. . . ] The actual effect depends on the source played. PORTABLE STEREO CD SYSTEM 22 RQT5142 Using auxiliary equipment You can play or record sound from other equipment through this unit's AUX IN terminal. Plug type: 3. 5 mm stereo AUX IN Playback OUT Preparation: (when using batteries) Press [ ]. Press [ ] to switch to AUX mode. Start playback on the equipment. Recording Do steps Press [ and ]. as described above. When this unit and the other equipment are connected to each other, do not set input on both unit's to "AUX". This can cause feedback noise to occur. Using headphones (not included) Reduce volume before connection. Avoid listening for prolonged periods of time to prevent hearing damage. [. . . ]