User manual PANASONIC RX-ES25

[. . . ] Portable Stereo CD System Operating Instructions Model No. RX-ES25 RX-ES20 Note: The "EB" indication shown on the packing case indicates United Kingdom. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. EB GN RQT5189-1B Dear Customer Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Precautions · · Avoid using or placing this unit near sources of heat. [. . . ] (Interference may also cause it to stop. Start auto-tuning again if this occurs. ) To stop auto-tuning Press [REW / ­ / Q] or [R / + / FF]. D s To improve reception FM: Change the length and direction of the antenna. Note · AM reception is briefly interrupted if [0 DECK] is pressed. · To improve reception when using the unit in a building or vehicle, use it near a window. A 212 7 7·7 The Radio (when using batteries) Press [ /I ]. Preset tuning Tuning is simpler if you preset stations. You can preset 12 FM and 12 AM stations. A SLEEP TIMER FADER DISPLAY Presetting radio stations B 7 Preset channel C 7 1 7 2 7 PRESET EQ TAPE TUNER CD TUNER S. VIRTUALIZER REW FF AUTO SCAN PRESET TUNE CD SKIP ­ VOLUME + 12 7·7 Indicates preset scan PRESET TUNE CD SKIP PRESET TUNE CD SKIP 1 7 2 7 2 7 1 4 7 2 5 8 3 6 9 PGM/-CLEAR 10 0 1 7 Preparation: Tune to the station you want to preset. (\ page 8) 1 s Press [·MEMORY CLEAR]. 2 s Turn [TIME/PRESET TUNE * While " " is flashing On the remote control Press the numbered button(s) to enter the station into a channel (1 to 12). To enter channel 10, 11 or 12 Press [10], then the two digits. If " " goes off during presetting, return to step s . 1 Selecting channels Preparation: Press [TUNER BAND] to select "FM" or "AM". B s Turn [TIME/PRESET TUNE the channel. CD SKIP ] to select On the remote control Press the numbered button(s) to select the channel (1 to 12). To select channel 10, 11 or 12, press [10], then the two digits. C Using preset scan You can search for a station by listening to all preset channels for 8 seconds each. Remote control only Preparation: Press [TUNER] to select "FM" or "AM". 1 Press and the [ S / s appears onholddisplay. 4 ] or [ 3 / T ] until "PS" Preset scan starts. 2 Press channel. s desired[ S / 4 ] or [ 3 / T ] when you find the Preset scan ends after searching through each preset channel once. To stop during the process, press [S / 4] or [3 / T ]. 3 Cancelling a preset channel 1 2 3 4 e. g. If channel 3 is not needed Select channel 3. While " " is flashing Turn [TIME/PRESET TUNE CD SKIP ] to display "­ ­". Now, when you perform preset scan or turn [TIME/PRESET TUNE CD SKIP ] to select a preset channel, channel 3 is skipped. Hints · To select the cancelled channel, press the remote control's numbered buttons. · You can press [S / 4] or [3 / T ] on the remote control for 3 turning of [TIME/PRESET TUNE CD SKIP ] described above. RQT5189 Listening CD SKIP ] to select a channel and press [·MEMORY*CLEAR]. 9 TAPE / CD 2 7 CDs 1 s Press [0 CD] to open the tray. (The unit comes on. ) Load a CD and press [0 CD] to close the tray. 2 s Press [6 CD] to start play. [. . . ] The remaining time is shown for about 5 seconds. To change the setting Press [SLEEP] to select the new time. Note You can use sleep timer in combination with play and record timer. Make sure the unit is off before the play/record timer's start time. B The Timer Fader Remote control only Troubleshooting Before requesting service, make the below checks. If you can't fix the unit as described below, or if something not listed here occurs, refer to the enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer. [. . . ]