User manual PANASONIC RX-ES27

[. . . ] Please note them in the space provided below and keep for future reference. SERIAL NUMBER RX-ES27 CAUTION! THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. [. . . ] If the surfaces are extremely dirty, use a soft cloth dipped in a soap-and-water solution or a weak detergent solution. ·Never use alcohol, paint thinner, or benzine to clean this unit. ·Before using chemically treated cloth, read the instructions that came with the cloth carefully. PHONES For a cleaner crisper sound Clean the heads regularly to assure good quality playback and recording. Use a cleaning tape (not included). RQT5671 re-ex1(p01-p09)[P] 9 00. 12. 28, 4:57 PM Before use Press [CLOCK/TIMER] to select "CLOCK". 9 CDs Press [POWER, ] to turn the unit on. Press [9 TAPE/CD] to switch to CD mode. 9 Each time the button is pressed CD TAPE Press [/ CD] to open the tray, load a CD, and / press [/ CD] to close the tray. B; Plays to the end of the CD and stops. Turn [­ "VOLUME#+] to adjust the volume. # Listening To stop play Press [ PLAY RE FADER SLEEP EQ ON TAPE/CD]. 1 PGM REC ALL 1-REC ST MONO RANDOM One touch play (When using AC power) When a CD is loaded, press [ CD]. The unit comes on and play starts. Displayed when CD not loaded To pause play Press [ CD] during play. Press again to resume play. Label To skip tracks Press [REW/­/ ] (backward) or [ /+/FF] (forward). Searching through tracks PLAY RE FADER SLEEP EQ ON 1 PGM REC ALL 1-REC ST MONO RANDOM Press and hold [REW/­/ (forward) during play. ] (backward) or [ /+/FF] Number of tracks Total playing time If this unit causes interference to other equipment (radios and televisions) separate it from the equipment. PLAY RE FADER SLEEP EQ ON 1 PGM REC ALL 1-REC ST MONO RANDOM CD selection Choose CDs with this mark: ( ) This unit can play CD-DA format audio CD-R and CD-RW that have been finalized upon completion of recording. It may not be able to play some CD-R or CD-RW due to the condition of the recording. (Interference may also cause it to stop. Start auto-tuning again if this occurs. ) To stop auto-tuning Press [REW/­/ ] or [ /+/FF]. FADER SLEEP EQ ON 1 PGM REC ALL 1-REC ST MONO RANDOM FADER SLEEP EQ ON 1 PGM REC ALL 1-REC ST MONO RANDOM Using auto scan Remote control only FADER SLEEP EQ ON 1 PGM REC ALL 1-REC ST MONO RANDOM You can search for a station by listening to all tuned-in stations for 8 seconds each. 1 s Press [TUNER] to select "FM" or "AM". SCAN] when you find the deAuto scan starts. Auto scan ends when it reaches the original frequency again. To stop during the process, press [AUTO SCAN]. To improve reception Auto scan 1 PGM FM: Change the length and position of the antenna. AM: Change the facing of the unit. FADER SLEEP REC EQ ON ALL 1-REC MONO RANDOM ·AM reception is briefly interrupted if a tape deck is operated. ·To improve reception when using the unit in a building or vehicle use it near a window. FADER SLEEP EQ ON 1 PGM REC ALL 1-REC MONO RANDOM If noise is excessive in FM Remote control only FM AM Press [FM MODE/BP] to display " Monaural sound is selected (" duces when reception is weak. MONO ". " goes off) and noise re- Press [FM MODE/BP] again to cancel the mode. To receive FM broadcasts allocated in 0. 1MHz 4 7 5 8 6 9 10 1 PGM FADER SLEEP REC EQ ON ALL 1-REC ST MONO RANDOM 0 CD PLAY AUTO SCAN C-RESET FM MODE BP MODE CLOCK TIMER P TAPE TUNER CD Main unit only First press [TUNER BAND] to select "AM". The display changes in a few seconds to show the current lowest FM frequency. The minimum frequency changes and the step is changed at the same time. Changing the step erases all preset stations. Repeat the above to change the step back. 13 RQT5671 re-ex1(p10-p15)[P] 13 00. 12. 28, 4:58 PM Listening The Radio: preset tuning Y Presetting radio stations Remote control only Tuning is simpler if you preset stations. [. . . ] Insert batteries or use household AC power. ("UO2" appears only if you have inserted memory batteries. ) Clean the CD Wait for about an hour for condensation to clear and try again. Replace the CD if it is scratched, warped, or irregularly shaped. CD CD won't play or CD display is incorrect Ä Ä Ä Ü Cassette deck Recording not possible Poor sound quality Have the cassette's tabs been removed?Clean the heads. 9 Radio A lot of noise or difficult to tune Interference may be caused by other equipment. [. . . ]