User manual PANASONIC S-100PU1E5

[. . . ] Operating Instructions Air Conditioner * Shows U1 type (4-Way Cassette) Model No. Indoor Units 4-Way Cassette S-36PU1E5 S-45PU1E5 S-50PU1E5 S-60PU1E5 S-71PU1E5 S-100PU1E5 S-125PU1E5 S-140PU1E5 Indoor Units Low Silhouette Ducted S-36PF1E5 S-45PF1E5 S-50PF1E5 S-60PF1E5 S-71PF1E5 S-100PF1E5 S-125PF1E5 S-140PF1E5 Outdoor Units Single Split (Single-phase) ?U-60PE1E5 U-71PE1E5 U-100PE1E5 U-125PE1E5 U-140PE1E5 * Shows F1 type (Low Silhouette Ducted) (3-phase) ?U-71PE1E8 U-100PE1E8 U-125PE1E8 U-140PE1E8 ENGLISH 2 ~ 13 Before operating the unit, read these operating instructions thoroughly and keep them for future reference. [. . . ] Then, the airflow can be set from the top position by pressing the FLAP button again. Indicator when swing operation is stopped Fan and heating Cooling and drying During cooling or drying operation, the flap will not stop at the downward position. Even if the flap is stopped at the downward position during the swing operation, it will not stop until it moves to the third position from the top. 8 01_F568247_EN. fm Page 9 Thursday, November 17, 2011 8:55 PM ADJUSTING AIRFLOW DIRECTION (CONTINUED) U1 type air conditioner is equipped with auto flaps. You can set the airflow direction to a specific angle or to the sweep mode using the remote controller. Do not move the flap with your hands. 4-way (U1 type) ?? The air outlet flap can be easily removed and washed with water. Be sure to always stop operation before removing the flap. After washing with water, allow it to dry, and then remount it with the arrow facing outward. Concealed duct type (F1) This air conditioner is not equipped with air outlet parts. Please refer to the manual of the locally adopted air outlet parts. 9 01_F568247_EN. fm Page 10 Thursday, November 17, 2011 8:55 PM ADJUSTING AIRFLOW DIRECTION FOR MULTIPLE INDOOR UNITS USING SINGLE REMOTE CONTROLLER (WIRED) ?The airflow direction cannot be set using the remote controller for the concealed duct type (F1). If multiple indoor units are connected to a remote controller, the airflow direction can be set for each indoor unit by selecting the indoor units (see the operation below). To set the airflow for individual units, press the UNIT button. Display shows the indoor unit number under group control. Set the airflow direction for the indoor unit that is shown on the display. Each time UNIT is pressed, the indicator changes in the order shown below. When nothing is displayed, you can make the setting for all indoor units in one operation. The unit number is displayed as Outdoor Unit Number?Indoor Unit Number. It varies depending on the number of units under group control. Two outdoor units and four indoor units Unit No. ? One outdoor unit and eight indoor units No display Unit No. 1?3 10 01_F568247_EN. fm Page 11 Thursday, November 17, 2011 8:55 PM SPECIAL REMARKS ??DRY??Once the room temperature reaches the level that was set, the unit repeats the cycle of turning on and off automatically. [. . . ] Reduce temperature settings or change to ?High?Refer to ?TIPS FOR ENERGY SAVING?. If your air conditioner still does not work properly although you checked the points as described above, first stop the operation and turn off the power switch. Then contact your dealer and report the serial number and symptom. Never repair your air conditioner by yourself since it is very dangerous for you to do so. [. . . ]