User manual PANASONIC S-60PK1E5

[. . . ] Operating Instructions Air Conditioner * Shows T1 type (Ceiling) Model No. Indoor Units 4-Way Cassette 6060 (Y1 type) S-36PY1E5 S-45PY1E5 S-50PY1E5 Indoor Units Wall Mounted (K1 type) S-36PK1E5 S-45PK1E5 S-50PK1E5 S-60PK1E5 S-71PK1E5 Indoor Units Ceiling (T1 type) S-36PT1E5 S-45PT1E5 S-50PT1E5 S-60PT1E5 S-71PT1E5 S-100PT1E5 S-125PT1E5 S-140PT1E5 Outdoor Units Single Split (Single-phase) U-60PE1E5 U-71PE1E5 U-100PE1E5 U-125PE1E5 U-140PE1E5 U-100PEY1E5 U-125PEY1E5 (3-phase) U-71PE1E8 U-100PE1E8 U-125PE1E8 U-140PE1E8 U-100PEY1E8 U-125PEY1E8 ENGLISH 2 ~ 13 Before operating the unit, read these operating instructions thoroughly and keep them for future reference. FRANAIS 14 ~ 25 Avant d?utiliser l?appareil, lisez ce mode d?emploi dans son intgralit et conservez-le pour toute rfrence ultrieure. ESPAOL 26 ~ 37 Antes de operar la unidad, lea atentamente estas instrucciones de funcionamiento y gurdelas para futuras consultas. [. . . ] ? The air outlet flap can be easily removed and washed with water. Be sure to always stop operation before removing the flap. After washing with water, allow it to dry, and then remount it with the arrow facing outward. Ceiling mounted type (T1) Vertical directions (automatic) This air conditioner is equipped with an auto flap. You can set the airflow direction to a specific angle or to the sweep mode using the remote controller. (Refer to the description of the remote controller. ) Do not move the flap with your hands. Horizontal directions (manual) The horizontal airflow direction can be adjusted manually by moving the vertical vanes to the left or right. Wall mounted type (K1) Vertical directions (automatic) Confirm that the remote controller has been turned on. Press the FLAP button to start the flap moving up and down. If you want to stop the flap movement and to direct the air in the desired direction, press the FLAP button again. In the cool mode, do not direct the flap down and move out of the cooling zone ?A?, otherwise, condensation may drip on to the floor. is the recommended flap position for cooling. When operating continuously in the fixed airflow direction setting for about an hour, the airflow direction is automatically controlled and the flap position is changed. The airflow direction may be different from the display on the remote controller. for heating Indoor unit Horizontal directions (manual) The horizontal airflow direction can be adjusted manually by moving the vertical vanes to the left or right. 9 01_85464609176012_EN. fm Page 10 Wednesday, October 3, 2012 1:49 PM ADJUSTING AIRFLOW DIRECTION FOR MULTIPLE INDOOR UNITS USING SINGLE REMOTE CONTROLLER (WIRED) ?If multiple indoor units are connected to a remote controller, the airflow direction can be set for each indoor unit by selecting the indoor units (see the operation below). To set the airflow for individual units, press the UNIT button. Display shows the indoor unit number under group control. Set the airflow direction for the indoor unit that is shown on the display. Each time UNIT is pressed, the indicator changes in the order shown below. When nothing is displayed, you can make the setting for all indoor units in one operation. The unit number is displayed as Outdoor Unit Number?Indoor Unit Number. It varies depending on the number of units under group control. Two outdoor units and four indoor units Unit No. ? One outdoor unit and eight indoor units No display Unit No. [. . . ] Reduce temperature settings or change to ?High?Refer to ?TIPS FOR ENERGY SAVING?. If your air conditioner still does not work properly although you checked the points as described above, first stop the operation and turn off the power switch. Then contact your dealer and report the serial number and symptom. Never repair your air conditioner by yourself since it is very dangerous for you to do so. [. . . ]