User manual PANASONIC SA-E10

[. . . ] These conditions can damage the cabinet and other components, thereby shortening the unit's service life. Do not place heavy items on the unit. CAUTION! Safety precautions Voltage Do not use high voltage power sources. This can overload the unit and cause a fire. Check the source carefully when setting the unit up on a ship or other place where DC is used. · DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE. [. . . ] · If you have only SPEAKERS B on and the input signal is multiVOLUME channel, the signal is down-mixed and "2CH MIX" appears on the DISC display. 0 -/-DIRECT TUNING · To turn off sound from SPEAKERS A, press [SPEAKERS A] so " A " goes off. SKIP SLOW/SEARCH · Note that if you are using DVD 6CH input (below), only the sound for STOP PAUSE PLAY the front speakers is output. · Speaker settings ( page 27) are fixed as follows when you have only DRIVE SELECT DVD RECORDER MANUAL SKIP SPEAKERS B on. Speaker size: LARGE NE TOUCH PLAY Subwoofer: NO (bass is outputOfrom the front speakers. ) NCTIONS FU ADVANCED DUAL AMP The Advanced Dual Amp activates automatically. In stereo sources or in 5. 1 channel, the unused surround back speakers amplifiers drive the ENTER front speakers for a clearer, purer sound. SUB MENU · [ADVANCED DUAL AMP] lights when the function is on. · RETURN can turn this function off You ( page 28). BI-AMP The bi-amp activates if you have bi-wired your front speakers and play analogue or stereo PCM sources. The amplifiers for the front and surround speakers separately run the low frequency and high frequency. You can use this feature in combination with the Advanced Dual Amp ( above) for an even clearer and purer stereo sound. · [BI-AMP] lights when the TV function is on. LEVEL · Bi-wire your front speakers ( page EFFECT · VOL make bi-amp settings To 13). NEO:6 TV/AV · Make sure you have selected "YES" for the "LR BI-WIRE setting" ( page AUTO Note SFC 27). This unit switches on, input switches to "DVR", and multi-channel play starts. Press [+ VOLUME -] to adjust the volume. You can also adjust the volume with VIERA's remote control. (An indicator appears on the television showing that you are adjusting this unit's volume. ) If the beginning of the program is cut off, press [u SKIP] to skip back to the beginning. STOP DRIVE SELECT PLAY MANUAL SKIP For your reference · If you switch your VIERA off, this unit also switches off (unless you have changed the input source to "TUNER" or "CD"). · VIERA's speakers start to output the audio instead if you switch this unit off. If you then switch this unit on again, audio output switches back to this unit. · If this unit is off and you switch the setting on your VIERA so that audio is output from a connected receiver, this unit switches on and starts to output the audio. NU DIRECT NAVIGATOR TOUCH PLAY ONE NCTIONS FU TOP ME ENTER Multi-channel audio for your VIERA SUB MENU RETURN · Connect your VIERA's digital output terminal to the DIGITAL IN OPTICAL 1 terminal on this unit ( page 9). · Refer to your VIERA's operating instructions and make the settings necessary to switch audio output from VIERA's speakers to SUBWOOFER TV speakers connected to this unit. OFF DIMMER · The input LEVEL EFFECT VOL unit switches to "TV" if you select a channel or otherwise operate the television ( page 34). source on this NEO:6 TV/AV To turn off VIERA Link "HDAVI Control", "HDMI settings", page 29. SFC MUSIC MOVIE AUTO TEST MUTING RQTV0247 21 Surround sound There are various modes you can use to add surround effects or play stereo through more than just the normal two speakers. Surround sound ENGLISH Dolby Pro Logicx RECEIVER AV SYSTEM TV TUNER CD BAND VCR RECORDER DVD PLAYER BD/DVD ANALOG 6CH · This feature adds surround effects to stereo sources. [. . . ] · Should you be playing a chapter on a DVD: - Change the audio output setting on the DVD player or DVD recorder from "Bitstream" to "PCM". (6. 1-channel sources will however be played as 5. 1-channel. ) - Select "PCMFIX" as instructed in "Input signals" when you play 2-channel sources. · The equipment connected by the HDMI cable is not compatible with the unit's copyright protection technology. · The unit has received a signal for a picture format that is incompatible with the HDMI connection. [. . . ]