User manual PANASONIC SA-EX140

[. . . ] 2 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 The remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Step Home Theater connections. . . . [. . . ] Sound will now come from the surround back speaker. RQT7492 Step 4 13 C RS LS SW Control guide Main unit Standby indicator [^] When the unit is connected to the AC mains supply, this indicator lights up in standby mode and goes out when the unit is turned on. [SPEAKERS, A, B] For selecting speakers A or B. Turning the speakers off automatically engages the STEREO/2CH MIX mode (when listening through headphones, for example). [% DIGITAL EX, % DIGITAL, % PL , DTS 96/24, DTS-ES, DTS, DTS NEO:6] Lights to indicate the source's input signal and decoding format used. % DIGITAL EX: Dolby Digital Surround EX sources % DIGITAL: Dolby Digital sources % PL : Dolby Pro Logic decoder is being used DTS 96/24: DTS 96/24 sources DTS-ES: DTS-ES discrete or matrix sources DTS: DTS sources DTS NEO:6: DTS NEO:6 matrix decoder is being used [MULTI CONTROL] Press to enter Multi control mode, and use [INPUT SELECTOR] to select/enter. [INPUT SELECTOR] For selecting input. Selects/Enters each setting in Multi control mode. Standby/on switch [8] Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. [VOLUME] Volume control. MULTI CONTROL INPUT SELECTOR VOLUME SPEAKERS A B PUSH ENTER Remote control signal sensor 6. 1CH DECODING DOWN UP VCR 2 PHONES VIDEO IN L AUDIO IN R [VCR 2] For a video camera, etc. [6. 1CH DECODING] For turning on the 6. 1 channel decoding mode. When using this mode the indicator lights. [PHONES] Headphone jack Plug type: 6. 3 mm stereo · Avoid listening for prolonged periods of time to prevent hearing damage. · Turn the speakers off when using the headphones. [BASS SYNTHESIZER] For turning on the bass synthesizer mode. When using this mode the indicator lights. [MULTI-SOURCE RE-MASTER] For selecting a re-master mode. When using this mode the indicator lights. [TUNE 2, 1] For tuning the radio and selecting preset stations. Press and hold until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found. Display · When you turn the dimmer to "ON", the following indicators change to dim. [­ SPEAKERS­ , ] Speaker indicators :Sound is output from speakers connected to the front A, surround, and center terminals. · If the frequency has not been input correctly, "ERROR" will be displayed. Automatic tuning Hold down [TUNE 2 or 1] until the frequency begins to scroll. (Tuning may stop if there is interference. ) Multi control tuner settings MULTI CONTROL 1 Enter Multi control mode. MULTI CONTROL Select MANUAL or PRESET tuning mode MANUAL: To tune the station frequency. PRESET: To select the preset channel. 1. Select. INPUT SELECTOR INPUT SELECTOR 2. Select. INPUT SELECTOR INPUT SELECTOR 3. Select. INPUT SELECTOR INPUT SELECTOR PUSH ENTER Main menu is displayed. (Multi control mode menus and factory settings á back cover) TUNER INPUT SELECTOR INPUT SELECTOR TUNING INPUT SELECTOR INPUT SELECTOR MANUAL MANUAL PRESET 2 Operations Change the settings. FM mode You can improve FM reception by switching reception to monaural. 1. Select "MONO". INPUT SELECTOR INPUT SELECTOR · To cancel, select "AUTO". Beat proof mode When there is a lot of noise interference with the AM broadcast, try switching to this mode. This may change the volume, but noise will also reduce. Select "MODE A" or "MODE B". INPUT SELECTOR INPUT SELECTOR INPUT SELECTOR INPUT SELECTOR INPUT SELECTOR INPUT SELECTOR AM allocation To change the AM frequency step. 1. Select "AM ALLOC". INPUT SELECTOR INPUT SELECTOR INPUT SELECTOR INPUT SELECTOR 3. [. . . ] · · · · · · · · Turn the volume up. Check connections to speakers and other equipment. Change the D-INPUT setting to suit the type of connection you have made. Check that the digital signals can be decoded by this unit. [. . . ]