User manual PANASONIC SA-HT56

[. . . ] Home Theater Audio System Model No. Operating Instructions SC-HT56 Dear customer Thank you for purchasing this product. Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference. If you have any questions contact 1-800-211-PANA (7262) The warranty can be found on page 23. As an ENERGY STAR Partner, Panasonic has determined that this product meets the ENERGY STAR guidelines for energy efficiency. P RQTX0175-2P IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. [. . . ] · The calibration will give optimal result for "DISTANCE". Therefore, you are unable to adjust the setting manually. Troubleshooting for auto speaker setup While performing auto speaker setup, errors may occur and the messages will blink or scroll on the display, depending on the conditions. Press any button on the main unit or remote control to stop the setup. -AUTO SETUP After troubleshooting, press and hold Message "INSERT MIC" "CHECK CONNECTION TO LS/RS SPEAKERS" "CHECK CONNECTION TO L/R SPEAKERS" Note to start the setup process again. Solutions Pages 11 6 6 · Calibration microphone is not detected. · One of the surround speakers is not detected. · Check the front (L) and (R) connections. 12 RQTX0175 · · · · Auto speaker setup may produce an unsatisfactory result with some speaker setups and configurations. Auto speaker setup will not start if you have muted the speakers. Auto speaker setup will not start if you have plugged in headphone. VIERA Link "HDAVI ControlTM" ( page 8) is disabled during auto speaker setup. Settings Change the settings to suit your equipment to the environment in which you are using it. Before making any changes, read the descriptions of the settings, note the factory settings and ranges, and refer to the equipment's instructions. Display Switch on. 1 Enter the setup mode. 2 Select the item you want to change. 3 Change the setting. 4 Exit the setup mode. Settings 2a Select and press [ENTER]. DISTANCE AUTO SETUP INPUT MODE HDMI DRCOMP ATTENUATOR REMOTE TV DELAY RESET EXIT Press and hold. · Refer to pages 13 and 14 for each item settings. · For "REMOTE", refer to page 21. · For "RESET", refer to page 19. 2b Select and press [ENTER]. Note Press to change the setting. Press repeatedly until "EXIT" appears. Press once to enter. Press [ENTER] to completely exit the setup mode. Auto speaker setup calibration will give optimal result for "DISTANCE". Therefore, you are unable to adjust the setting manually. 2a 2b LR C S Repeat for each speaker channel 3 feet to 30 feet 3 Distance · Enter the distance of the front, center and surround speakers from the seating position. DISTANCE Change the distance so that the sound from all the speakers (except for the subwoofer) reaches you at the same time. You can select distances between 3 feet and 30 feet. The factory settings are: LR (front): C (center): S (surround): 10 ft (feet) 10 ft (feet) 5 ft (feet) Auto setup · Reset the settings done in auto speaker setup. AUTO SETUP DEFAULT NO YES YES: Reset all auto speaker setup settings NO: To cancel (factory setting) Input mode · This unit automatically detects whether input is digital or analog, but you can fix the input mode. INPUT MODE TV DVR DVD AUTO ANALOG DIG PCMFIX AUTO: The unit automatically detects whether input is digital or analog. (factory setting) ANALOG: Select to make the unit accept analog input. DIG: Select to make the unit accept digital input. PCMFIX1: Select to input to PCM. 1 In rare cases, the unit may have trouble recognizing PCM signals and this may cause the beginning of tracks to be cut off. [. . . ] Replacement parts -- When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards. Safety check -- After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working condition. The servicer will require all components to service your system. [. . . ]