User manual PANASONIC SB-TP55EB

[. . . ] Use numbers indicated in parentheses when asking for replacement parts. 1 (RJA0038-1U) Note The included AC mains lead is for use with this unit only. 1 (RJL1P015B50) WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS. This product may receive radio interference caused by mobile telephones during use. [. . . ] The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Brown or Red. Service Do not attempt to repair this unit by yourself. If sound is interrupted, indicators fail to light, smoke appears, or any other problem that is not covered in these operating instructions occurs, disconnect the AC mains lead and contact your dealer or an authorized service center. Electric shock or damage to the unit can occur if the unit is repaired, disassembled or reconstructed by unqualified persons. Extend operating life by disconnecting the unit from the power source if it is not to be used for a long time. WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E, BY THE EARTH SYMBOL n OR COLOURED GREEN OR GREEN/YELLOW. THIS PLUG IS NOT WATERPROOF--KEEP DRY. Before use Remove the connector cover. How to replace the fuse The location of the fuse differ according to the type of AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug. Open the fuse cover with a screwdriver. Figure A Figure B Fuse cover 2. Replace the fuse and close or attach the fuse cover. Figure B Figure A 2 RQT6905 Fuse (5 ampere) Fuse (5 ampere) Insertion of connector Even when the connector is perfectly inserted, depending on the type of inlet used, the front part of the connector may jut out as shown in the drawing. However there is no problem using the unit. Connector Approx. 6 mm Appliance inlet y ; y ; Speaker setup Take care when handling the speakers not to apply undue pressure to the front nets. Lay the speakers on a flat surface over a soft cloth when working on them. Tighten the screws firmly. 270 mm ; ; ; 10 mm 30-35 mm ø7. 5-9. 5 mm 7-9 mm 60 mm Center speaker (SB-PC50) Put above or below the center of the television, on a shelf or rack or attach to the wall. Placing it directly on the television can cause the picture to be distorted. Do not attach this speaker to walls or ceilings using methods other than those described here. Front and surround speakers (SB-FS50) The 4 speakers are the same. Put the front speakers either side of the television. Put the surround speakers to the side of or slightly behind the seating area. Do not attach these speakers to walls or ceilings. Attaching the rubber feet when placing on a surface Attach the rubber feet to the base of the speaker to prevent vibration from causing the speaker to move or fall over. Attaching the base Screw for base Place with the net up. Attaching to a wall Attach four rubber feet to the rear of the speaker. Screw (not included) Screw the wood screw into a thick and hard part of the wall. The surface must be able to support over 10 kg. Refitting the stabilizer Refit the stabilizer if you place the speaker so that there are more than 20 cm between its rear and a wall. Turn the stabilizer around and reattach with the four screws. Attaching to a television stand Ensure the following conditions are met when purchasing or preparing your television stand. [. . . ] If this occurs, turn the television off for about 30 minutes. The television's demagnetizing function should correct the problem. If it persists, move the speakers further away from the television. Specifications are subject to change without notice. Mass and dimensions are approximate. You cannot remove the speaker net. [. . . ]