User manual PANASONIC SC-RT50

[. . . ] Operating Instructions Recordable DVD Home Theater System Model No. SC-RT50 E ST P 1 2 3 4 Front speaker assembly Positioning and connection of speakers Video connections Radio and AC cord connections Plug-in Auto Tuning All necessary steps of setup are completed. Please see the Operations Guide for recording and playback operation. Channel captions ···································· 14 Set Clock Manually ·································· 15 ·································· 15 Selecting television type ·························· 14 Adjust Time Zone Television operation ································· 15 Speaker installation options ······ Back cover When other Panasonic products respond to this remote control ··················· 15 E ST P E ST P E ST P Other settings and optional speaker installation (Perform if necessary) P 1 RQT8656-P Front speaker assembly Preparation For assembly, use a Phillips-head screwdriver. Make sure you have all the indicated components before starting assembly, positioning, and connection. [. . . ] Place the antenna where reception is best. Keep loose antenna cable away from other wires and cables. FM indoor antenna Affix this end of the antenna where reception is best. Adhesive tape Loosen the terminal with a Phillips-head screwdriver. Push up. Insert the antenna cables fully. White Red Black Tighten the terminal screw again. Back of the main unit 2 Connect the AC power supply cord. AC IN terminal To household AC outlet (AC 120 V, 60 Hz) Conserving power The main unit consumes a small amount of power, even when it is turned off (approx. To save power when the unit is not to be used for a long time, unplug it from the household AC outlet. Set the unit to standby mode and remove the AC power supply cord after "BYE" disappears from the unit's display. You will need to reset some memory items in the unit after plugging. Back of the main unit AC power supply cord Note The included AC power supply cord is for use with this unit only. Also, do not use cords for other equipment with this unit. 11 Plug-in Auto Tuning After pressing [] to turn the unit on for the first time, the unit starts necessary setup. If the setup screen does not appear, press [DRIVE SELECT], and turn the power off and on again. 1 2 Included parts to be used Remote control 2 Batteries Turn on the television and select the appropriate video input to suit the connections to this unit. Press [THEATER] to switch the remote control to operate this unit. Press []. Select Language Seleccione el idioma Sélection de Langue Preparation English Español Français Press ENTER Pulse ENTER Appuyer sur ENTER Insert the included batteries into the remote control. Press [, ] to select the language and press [ENTER]. If you make a mistake, press [RETURN] to return to an earlier screen. Aspect Ratio Selection Insert so the poles ( and ) match those in the remote control. R6/LR6, AA Select TV type and press ENTER. (Please refer to Operation Instruction for details) 4:3 16:9 4:3 TV 16:9 Widescreen TV POWER /I CH Remote control signal sensor THEATER TV Press [, ] to select the aspect ratio that fits your television best ("4:3 TV" or "16:9 Widescreen TV"), and then press [ENTER]. Quick Start setting The unit can be turned on faster, in about 1 second. Please note that Quick Start mode slightly increases power consumption when the unit is off. (See Operation Instructions for details) Turn Quick Start on ?On DRIVE SELECT Numbered buttons CANCEL TV operation buttons CH Off Press [, ] to select "On" or "Off" and press [ENTER]. If you activate "Quick Start" function, select "On". About "Quick Start" function If you set Quick Start to on, you can start recording to DVDRAM about 1 second after you press [] to turn the unit on and then sequentially press [ REC]. The following happens when you have selected "On". Power consumption in standby mode increases because power is supplied to the unit. RETURN SETUP Default Recording Source Please select the source from which this unit will record each time it is turned on. [. . . ] Press [, ] to select "Setup" and press []. Press [, ] to select "Clock Settings" and press [ENTER]. Press [, ] to select "Adjust Time Zone" and press [ENTER]. Press [, ] to select "­1" or "+1" and press [ENTER]. Remote Control Code Press " " and "ENTER" together for more than 2 seconds on the remote. Channel Setup Disc Video To change the code on the remote control While pressing [ENTER], press and hold the numbered button ([1], [2] or [3]) for more than 2 seconds. [. . . ]