User manual PANASONIC SC-DK3

[. . . ] Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 5) Do not use this apparatus near water. 7) Do not block any ventilation openings. [. . . ] · Peripheral equipment and cables sold separately unless otherwise indicated. · To connect equipment, refer to the appropriate operating instructions. Start performing auto speaker setup. a) Press and hold . · [AUTO SPEAKER SETUP] indicator starts flashing. AUTO SPEAKER SETUP AUTO SPEAKER SETUP Auto speaker setup · "AUTO SETUP" appears on the display. b) The unit checks that you have correctly connected the calibration microphone. c) The automatic setup starts with STEP 1, STEP 2, and STEP 3 calibration as follows. STEP1 ­ DETECTION/DISTANCE STEP2 ­ FREQUENCY STEP3 ­ LEVEL For your reference · Loud test tones are output from each speaker during the configuration. · During setup, operations may stop when there is an error message on the display. Refer below for troubleshooting. Auto speaker setup finishes. · "COMPLETE" appears on the display and all calibrations are saved. · [AUTO SPEAKER SETUP] indicator lights. -AUTO SETUP · To exit, press and hold . · Disconnect the calibration microphone. To cancel during setup Press any button on the main unit or remote control. "CANCELED" appears on the display. Note · Perform auto speaker setup again if you have changed the speakers, speaker positions, or the layout of your listening environment. DIG: Select to make the unit accept digital input. PCMFIX1: Select to input to PCM. 1 In rare cases, the unit may have trouble recognizing PCM signals and this may cause the beginning of tracks to be cut off. Select "PCMFIX" if this occurs. Note When a FIX mode is on, the unit cannot process other signals. If this occurs, select an input mode other than PCMFIX, or cancel the DTS FIX mode. (continue on next page) RQTX0175 · With DTS, the signals may not be recognized at all. To engage the DTS FIX mode: Press and hold [-MENU] and [ENTER] at the same time. To cancel the DTS FIX mode: Press and hold [-MENU] and [ENTER] at the same time. The mode cancels when input mode is set to AUTO or when the unit is turned off. 13 Settings Switch on. Display 2a 2b STNBY 3 HDMI settings · · Settings To reduce standby power consumption. Choice for turning off the VIERA Link "HDAVI ControlTM" ( page 8). VIERA Link "HDAVI Control" OFF: VIERA Link "HDAVI Control" is OFF ON: VIERA Link "HDAVI Control" is ON (factory setting) HDMI Standby selection OFF: Standby power consumption reduced (approximately 0. 3 W). · Signals from DVD equipment cannot pass through HDMI connection to the television when the unit is in standby ( page 8). [. . . ] 9. 5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Phone (787)750-4300, Fax (787)768-2910 RQTX0175 You may also contact us directly at: 1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday ­ Friday 9 am to 8 pm, EST. ) Panasonic Service and Technology Company 20421 84th Avenue South, Kent, WA 98032 (We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks) 23 Limited Warranty Product Service 1. Damage requiring service -- The unit should be serviced by qualified service personnel if: (a) The AC power supply cord or the plug has been damaged; or (b) Objects or liquids have gotten into the unit; or (c) The unit has been exposed to rain; or (d) The unit does not operate normally or exhibits a marked change in performance; or (e) The unit has been dropped or the cabinet damaged. Servicing -- Do not attempt to service the unit beyond that described in these operating instructions. Refer all other servicing to authorized servicing personnel. [. . . ]