User manual PANASONIC SC-EH500

[. . . ] These operating instructions are applicable to the following systems. These operating instructions, however, fundamentally explain the operation of system SC-EH500. [EH790]: indicates a function which can be enjoyed with SC-EH500 only. [EH590]: indicates a function which can be enjoyed with SC-EH590 only. Supplied accessories Please check and identify the supplied accessories. [. . . ] Preparation: Press [Í/I] to turn the unit on. 1 2 3 DISC 4 5 6 S10/-/-- 7 8 9 0 1 3 A ª Direct access play [EH790] Starts normal play from a selected track on a selected disc to the last track of the final disc ( page 8). [EH590] Starts normal play from a selected track to the last track. Í/I 2 31 4 1 2 3 Press [TUNER/BAND] to select FM or AM. Each time you press the button: FMbAM TEST ÎPRO LOGIC SUPER SRND Press [TUNING MODE] to select "MANUAL". Each time you press the button: MANUALbPRESET 3D AI EQ CH SELECT AV EFFECT Remote control only Press [TUNING (X or W)] to tune in the desired broadcast. If you press and hold [TUNING (X or W)] for a moment, the frequency starts changing automatically. It may also stop if there is outside interference. Press and hold [TUNING (X or W)] again to restart. You can also stop the frequency changing by pressing [TUNING (X or W)]. "TUNED" is displayed when a radio station is tuned. "ST" is displayed when a stereo FM broadcast is being received. SUPER SOUND EQ DIGITAL S. WOOFER 1 CD VCR/AUX/ TAPE/ 6CH INPUT DECK 1/2 CD DISPLAY TUNER/ BAND 2/; 1 MUTING XsALBUMW VOLUME 2 [EH790] 1 Press [DISC]. 2 Within 10 seconds or so Press [1]-[5] to select the disc. [EH790] (WMA/MP3 only) Press and hold [­ALBUM (X or W)] to select the album. Select the track with the numbered buttons. To select a 2-digit number e. g. To select track 21, press [S10/-/--]>[2]>[1] To select a 3-digit number [EH790] e. g. FM stations are preset into channels 1 to 39, and AM stations are preset into channels 21 to 39. "SET OK" is shown when presetting is complete and the last station to be preset is played. "ERROR" is displayed if the tuner doesn't receive any stations. Do presetting manually if this happens (see below). MHz A SET 4 Press ["] (reverse side) or [!] (forward side). Play begins and the indicator changes to green. 1 DECK 1 4 231 DECK 2 Forward side Tape facing down 5 Adjust the volume. B 2 SET Note AM stations replace any FM channels that were preset in channels 21 to 39. 1 2 3 4 <OPEN To stop the tape Press []. [A] To change the deck to be used Press [DECK 1/2] to select the deck you want to play. B ª Manual presetting Preset the stations one at a time. DOLBY NR ÎNR 1 To listen to 2 tapes consecutively Insert a tape into each deck and select "f". Both tapes will be played 8 times each. 3 TUNING Basic operations 4 SET The station occupying a channel is erased if another station is preset in that channel. REV MODE ÎNR 1 Press [6] or [5] while the tape is stopped. To find the beginning of a track (TPS: Tape program sensor) C C ª Selecting channels Í Í SLEEP PROGRAM CANCEL Press [6] or [5] during play. Play resumes from the beginning. " Tape direction Each deck's play direction is stored in the system's memory. You can fast-forward or rewind the tape while you are playing or recording a tape in another deck. Press [DECK 1/2] to switch to the deck not playing, and then press [6] or [5]. After the above operation, be sure to press [DECK 1/2] to reselect the deck playing. Note TPS may not operate correctly in the following situations: If the interval between tracks is less than 4 seconds. If there are silent parts within tracks. [. . . ] Condensation may have formed in the changer or player due to a sudden change in temperature. Wait about an hour for it to clear and try again. There is a problem with the CD mechanism. (A power failure may have occurred. ) The tray will open automatically. [. . . ]