User manual PANASONIC SC-HTB10

[. . . ] Operating Instructions Home Theater Audio System Model No. SC-HTB10 Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Before connecting, operating or adjusting this product, please read the instructions completely. [. . . ] This standard is compatible with Panasonic's conventional HDAVI equipment. Please refer to individual manuals for other manufacturers' equipment supporting VIERA Link function. Specifications GENERAL Power consumption: Power consumption in standby mode: Approx. 0. 1 W Power supply: AC 120 V, 60 Hz 25 W SPEAKER SECTION FRONT SPEAKERS (BUILT-IN) Type: 1 way 1 speaker system (Bass Reflex) Full range: 6. 5 cm (21/2q) Cone typek2 SUBWOOFER (BUILT-IN) Type: 1 way 1 speaker system (Bass Reflex)k2 Woofer: 8 cm (31/8q) Cone typek2 AMPLIFIER SECTION RMS Output Power Front ch: 30 W per channel (4 ), 1 kHz, 10 % THD Subwoofer ch: 30 W per channel (4 ), 100 Hz, 10 % THD Total RMS Dolby Digital mode power: 120 W FTC Output Power Front ch: 20 W per channel (4 ), 120 Hz to 20 kHz, 1 % THD Subwoofer ch: 20 W per channel (4 ), 40 Hz to 120 Hz, 1 % THD Total FTC Dolby Digital mode power: 80 W 1 Specifications are subject to change without notice. 2 Total harmonic distortion is measured by a digital spectrum analyzer. Audio information Compatible audio formats This unit is compatible with the following formats: Dolby Digital, DTS Digital Surround, 2-channel LPCM and multi-channel LPCM. When using the optical digital audio cable, this system is not able to play audio with a sampling frequency greater than 48 kHz. (Sound Effect and Dolby Virtual Speaker will be automatically canceled if the audio signal's sampling frequency is greater than 48 kHz. ) Operating Instructions Dimensions (WkHkD): (Without wall mount bracket) 800 mmk108 mmk58 mm (311/2qk41/4qk29/32q) (With wall mount bracket) 800 mmk108 mmk80 mm (311/2qk41/4qk35/32q) Mass (Weight): (Without wall mount bracket) Approx. 3. 2 kg (7. 1 lbs) (With wall mount bracket) Approx. 3. 3 kg (7. 3 lbs) Operating temperature range: 0 oC to r40 oC (r32 oF to r104 oF) Operating humidity range: 20 % to 80 % RH (no condensation) TERMINAL SECTION HDMI This unit supports "HDAVI Control 5" function. HDMI input Input connector: Type A (19 pin) HDMI AV output Output connector: Type A (19 pin) Digital Audio Input (TV only) Optical digital input: Optical terminal Sampling frequency: 32 kHz, 44. 1 kHz, 48 kHz Audio Format: LPCM, Dolby Digital IR Blaster Terminal 1: 3. 5 mm (1/8q) jack 15 Troubleshooting Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the following guide do not solve the problem, refer to "Customer Services Directory (United States and Puerto Rico)" on page 19 if you reside in the U. S. A. or Puerto Rico, or refer to "Product information" on page 19 if you reside in Canada. General operation To return to the factory preset. While this unit is on, press [POWER Í/I] on this unit for more than 4 sec. (All the indicators will blink twice when the unit is reset. ) The remote control doesn't work properly. It is possible that the insulation sheet has not been removed. ( 7) The remote control and main unit are using different codes. ( 17) It may be necessary to set the code of the remote control again after changing the battery of the remote control. ( 17) This unit does not operate correctly. If the HDMI cable is connected to the wrong terminal (HDMI AV IN or HDMI AV OUT), this unit will not operate correctly. Turn this unit off, disconnect the AC power supply cord and reconnect the HDMI cable(s). ( 10) When operating the connected device, this unit reacts in an unwanted manner. HDAVI Control commands may use a different signal depending on the make of the device. In this case, set "VIERA Link" to "Off". [. . . ] Make sure that the lock pin does not get caught on the fall prevention cord. A Do not insert the lock pin farther than this point. 8 Drive 2 screws (not supplied) into the screwing positions identified in step 4. A B C D E At least 30 mm (13/16q) 4. 0 mm (5/32q) 7. 8 mm to 9. 4 mm (5/16q to 13/32q) Wall 5. 0 mm to 6. 0 mm (3/16q to 1/4q) Be sure to use commercially available screws with nominal diameter of 4. 0 mm (5/32q) suited to the wall surface material (wood, steel frame, concrete, etc. ) and also capable of supporting over 20 kg (44. 1 lbs) each for attaching this unit to the wall. The position in the wall where the screw is to be attached should be capable of supporting over 20 kg (44. 1 lbs). Improper attachment may result in damage to the wall and this unit. Installation Instructions Take care when fixing this unit to the wall. Always ensure that there are no electrical cables or pipes in the wall before hanging this unit. [. . . ]