User manual PANASONIC SC-HTB18EB

[. . . ] SC-HTB18_EB_VQT5J46. book 1 ページ ２０１４年３月１９日　水曜日　午前９時４７分 Operating Instructions Home Theater Audio System Model No. SC-HTB18 Thank you for purchasing this product. Please read these instructions carefully before using this product, and save this manual for future use. Included Installation Instructions The installation work should be done by a qualified installation specialist. ( 12 to 16) Before commencing work, carefully read these installation instructions and the operating instructions to ensure that installation is performed correctly. [. . . ] ≥ Place the main unit in front of the TV pedestal. Page 14 When attaching the main unit to a wall ≥ Place the main unit on a flat and vertical surface. Page 15 ∫ When placing the main unit in front of the TV The main unit may block or interfere with the TV’s various sensors (C. A. T. S. (Contrast Automatic Tracking System) sensor, remote control sensor, etc. ) and the 3D Eyewear transmitters on a 3D compatible TV. ≥If interference occurs, move the main unit further away from the TV. If the TV still does not function correctly, try using it in a rack or in the wall mount position. ∫ If the TV’s remote control sensor is blocked by the main unit Try using the TV’s remote control from a different angle. ≥ Place the subwoofer within a few meters of the main unit and in a horizontal position with the top panel facing upward. ≥ Do not use the main unit or the subwoofer in a metal cabinet. ≥ Placing the subwoofer too close to the walls and corners can result in excessive bass. Cover walls and windows with thick curtains. ≥ If irregular colouring occurs on your TV, turn the TV off for about 30 minutes. If it persists, move the main unit and subwoofer further away from the TV. Magnetised cards, watches, etc. , can be damaged if placed too close to the main unit and subwoofer. ≥ Keep the main unit approximately 150 mm away from the TV. VQT5J46 13 Getting started Precautions When placing the main unit on a rack or on a table SC-HTB18_EB_VQT5J46. book 14 ページ ２０１４年３月１９日　水曜日　午前９時４７分 When placing the main unit on a rack or on a table Additionally required accessories (commercially available) ≥Fall prevention cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1 ≥Screw eye (to attach the fall prevention cord). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . k 1 ≥ Use commercially available screws that are capable of supporting over 33 kg. ≥ Use a cord that is capable of supporting over 10 kg (with a diameter of about 2 mm). Slide the MULTI ANGLE switch to “RACK/TABLE TOP”. ≥Press the AC mains lead into the holder. Attach the cord to the main unit.  A Cord§ § If the cord cannot be threaded through the holes, try bending the cord in 2 locations, about 5 mm apart from the tip, at an angle of 45o (as illustrated above). Place the main unit in the desired position and attach the cord onto the rack or table. ≥ ≥ ≥ ≥ Make sure that the slack of the cord is minimal. Do not lean the main unit against the TV or wall. Do not place the main unit over the AC mains lead. Ensure that the main unit is stable.  B Screw eye ≥Attach at a position capable of supporting over 10 kg. ≥Depending on the placement of the main unit, the screwing position of the screw eye may differ. 14 VQT5J46 SC-HTB18_EB_VQT5J46. book 15 ページ ２０１４年３月１９日　水曜日　午前９時４７分 When attaching the main unit to a wall Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg. The screws and other items are not supplied as the type and size will vary with each installation. ≥Refer to step 3 for details about the required screws. ≥Be sure to attach the fall prevention cord as a secondary safety measure. [. . . ] ≥ When the remote control code is changed ( The indicators blink once. ≥ When changing the setting ( “To turn off the volume limitation”) ( 19) The indicators blink twice. ≥ When the main unit is reset ( 20) 19) Bluetooth® indicator blinks quickly. ≥ When the main unit is ready for pairing ( 11) Bluetooth® indicator blinks slowly. [. . . ]