User manual PANASONIC SC-HTB500

[. . . ] Operating Instructions Home Theater Audio System Model No. SC-HTB500 Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Before connecting, operating or adjusting this product, please read the instructions completely. [. . . ] HDMI input Input connector: Type A (19 pin) HDMI AV output Output connector: Type A (19 pin) Digital Audio Input (TV only) Optical digital input: Optical terminal Sampling frequency: 32 kHz, 44. 1 kHz, 48 kHz Audio Format: LPCM, Dolby Digital IR Blaster Terminal 1: 3. 5 mm jack WIRELESS SECTION Wireless module Frequency range: 2. 4 GHz to 2. 4835 GHz Number of channels: 3 AMPLIFIER SECTION RMS Output Power Front ch: 60 W per channel (4 ), 1 kHz, 10 % THD Subwoofer ch: 120 W per channel (8 ), 100 Hz, 10 % THD Total RMS Dolby Digital mode power: 240 W 1 Specifications are subject to change without notice. 2 Total harmonic distortion is measured by a digital spectrum analyzer. 17 Operating Instructions Audio information Compatible audio formats This unit is compatible with the following formats: Dolby Digital, DTS Digital Surround, 2-channel LPCM and multi-channel LPCM. When using the optical digital audio cable, this system is not able to play audio with a sampling frequency greater than 48 kHz. (Sound Effect and Dolby Virtual Speaker will be automatically cancelled if the audio signal's sampling frequency is greater than 48 kHz. ) When operating the connected device, this unit reacts in an unwanted manner. HDAVI Control commands may use a different signal depending on the make of the device. In this case, set "VIERA Link" to "Off". ( 20, "VIERA Link") VIERA Link related operations no longer function properly. Check the "VIERA Link" setting on the connected devices. When the HDMI connections are changed, after a power failure or after the AC mains lead has been removed, VIERA Link operations may not function properly. Troubleshooting Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the following guide do not solve the problem, consult your dealer for instructions. Power No power. ( 13) After turning this unit on, if the "TV, BD/DVD" indicator or the " D/DTS" indicator blinks and this unit immediately turns off, unplug the AC mains lead and consult your dealer. Power of this unit is turned off when the input for the TV is changed. This is a normal feature when using VIERA Link (HDAVI Control 4 or later). For details please read the operating instructions for the TV. General operation To return to the factory preset. While this unit is on, press [Í/I] on this unit for more than 4 sec. (All the indicators will blink twice when the unit is reset. ) The remote control doesn't work properly. It is possible that the insulation sheet has not been removed. ( 7) The remote control and this unit are using different codes. ( 20) It may be necessary to set the code of the remote control again after changing the battery of the remote control. ( 20) This unit does not operate correctly. If the HDMI cable is connected to the wrong terminal (HDMI AV IN or HDMI AV OUT), this unit will not operate correctly. Turn this unit off, disconnect the AC mains lead and reconnect the HDMI cable(s). [. . . ] Keep the screws out of reach of children to prevent swallowing. 27 9 Mount the unit securely onto the screws. A Move this unit so that the screw is in this position. Be sure that both the wall mount brackets are securely attached to the screws. If this unit is tilting forward, remove this unit from the screws and adjust by tightening the screws. 10 Push the lock pins fully into place. A Rear of this unit B Lock pin (supplied) C Screw (not supplied) Be sure to attach both lock pins correctly. 11 Attach the cord to a wall with a screw (not supplied). Keep the screws out of reach of children to prevent swallowing. Check the strength of the installation location. The position in the wall where the screw is to be attached should be capable of supporting over 20 kg. [. . . ]