User manual PANASONIC SC-PM10PC

[. . . ] CD Stereo System Operating Instructions Model No. SC-PM10 Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. PC RQT6675-1P Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. These operating instructions are applicable to the following system. Table of contents Before use Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Every time you press the button: FM AM 1 CD PLAY PLA MODE 2 5 8 0 CD 3 6 9 10 4 CD REC MODE 7 1 3 2 4 3 Press [TUNE MODE] on the remote control to select the manual tuning mode. Make sure that " PROGRAM " is not displayed. Before use TUNER BAND TAPE APE STOP VOL VOL FF 2 FM MODE TUNE MODE REW SOUND VIRTUALIZER VIRTUALIZER EQ BASS TREBLE MUTING MU ING PRESET DISPLAY DISPLA DIMMER Press [g/REW/4] or [3 /FF/ f] to select 4 3 the frequency of the required station. "TUNED" is displayed when a radio station is tuned. " ST " is displayed when a stereo FM broadcast is being received. Listening operations 1 4 TUNER BAND Adjust the volume. MHz 2 3 TUNE MODE Auto tuning Press and hold [ g/REW/4] or [3 /FF/ f] for a moment 4 3 until the frequency starts changing rapidly. The unit begins auto tuning, stopping when it finds a station. · Auto tuning may not function when there is excessive interference. · To cancel auto tuning, press [ g/REW/4] or [3 /FF/ f] 4 3 once again. A REW RE FF If noise is excessive in FM by remote control only Press [FM MODE] to display "MONO". MHz TUNED ST 4 This mode improves sound quality if reception is weak, but broadcasts will be heard in monaural. Press [FM MODE] again to cancel the mode. MONO is also cancelled if the frequency is changed. Turn off "MONO" for normal listening. Stereo and monaural broadcasts are automatically played as they are received. VOLUME FM allocation setting By adjusting the allocation, you can enable this tuner to receive FM broadcasts allocated in 0. 1 MHz steps. DOWN UP UP dB Preparation: Press [TUNER/BAND] to select "AM". After a few seconds, the display will change to a flashing display of the current minimum FM frequency. If you continue to hold the button down, the minimum frequency will change. To return to the original frequency indication, repeat above. Note A PROGRAM/ CLEAR CD PLAY PLA MODE CD REC MODE SLEEP CLOCK CL CK TIMER PLAY REC 1 4 7 2 5 8 0 CD 3 6 9 10 MHz TUNED MONO TUNER BAND TAPE APE STOP VOL FM MODE TUNE MODE REW SOUND PRESET VIRTUALIZER VIRTUALIZER EQ VOL FF BASS TREBLE FM MODE MUTING MU ING DISPLAY DISPLA DIMMER · After changing the "allocation" setting, the frequencies you previously preset in the memory will be cleared. · Sound is momentarily interrupted if you load/unload tapes while listening to an AM broadcast. 10 RQT6675 The radio: preset tuning by remote control only There are two methods of presetting stations. Automatic presetting: All the stations the tuner can receive are preset. Manual presetting: You can select the stations to preset and the order they are preset in. Up to 15 stations each can be set in the FM and AM bands. Preparation: Press [TUNER/BAND] to select "FM" or "AM". A Automatic presetting PROGRAM Press and hold [PROGRAM/­CLEAR]. The tuner presets all the stations it can receive into the channels in ascending order. When finished, the last station memorized is tuned in. PROGRAM MHz Manual presetting PROGRAM 1 Press 2 3 B Preset the stations one at a time. [PROGRAM/ ­ CLEAR] then press [g, REW/ 4] or [f, 3 / FF] to tune to the radio station. Press [PROGRAM/ ­CLEAR] then press [g, REW/ 4] or [f, 3 / FF] to select a memory number. Press [PROGRAM/­CLEAR]. The station occupying a memory number is erased if another station is preset in that memory number. Selecting channels Press the numbered buttons to select the channel. For channels 1 to 9 press the corresponding number. For channels 10 to 15 press [ 10], then the two digits. 1 Preset channel 1 Press [TUNE MODE] to select " PROGRAM ". [. . . ] Separate the antenna wire of the TV set from the unit. Clean the heads. (Back cover) If the erasure prevention tabs have been removed, cover the holes with adhesive tape. Replace the disc if it is scratched, warped, or non-standard. Condensation may have formed inside the unit due to a sudden change in temperature. [. . . ]