User manual PANASONIC SC-PM250BEB

[. . . ] Caution for AC mains lead For your safety, please read the following text carefully. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark body of the fuse. [. . . ] Keep in a cool, dark area. █ DAB+ section DAB memories 20 channels 1 Disposal of Old Equipment and Batteries Only for European Union and countries with recycling systems These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation. By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment. For more information about collection and recycling, please contact your local municipality. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. Note for the battery symbol (bottom symbol): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. Licenses MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson. The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Panasonic Corporation is under license. Other trademarks and trade names are those of their respective owners. ® Frequency band (wavelength) Band III 5A to 13F (174. 928 MHz to 239. 200 MHz) Sensitivity *BER 4x10-4 Min requirement DAB external antenna Terminal –98 dBm F - Connector (75 Ω) █ General Power supply Power consumption Dimensions (W x H x D) Mass Operating temperature range AC 220 V to 240 V, 50 Hz 14 W 184 mm x 123 mm x 235 mm 1. 1 kg 0°C to +40°C Connect the DAB antenna. Tape the antenna to a wall with the least amount of interference. Placement of speakers █ Disc section Disc played (8 cm or 12 cm) CD, CD-R/RW (CD-DA, MP3 ) MPEG-1 Layer 3, MPEG-2 Layer 3 Pick up Wavelength 790 nm (CD) Adhesive tape (not supplied) Use an outdoor antenna if the reception is poor. Operating humidity range 35% to 80% RH (no condensation) Power consumption in standby mode (With “BLUETOOTH STANDBY” set to “OFF”) 0. 2 W (approximate) Power consumption in standby mode (With “BLUETOOTH STANDBY” set to “ON”) 0. 3 W (approximate) Note: • Specifications are subject to change without notice. • Total harmonic distortion is measured by the digital spectrum analyser. 2 Connect the speakers. B A (6 ) (6 ) █ USB section USB port USB standard Media file format support USB device file system USB 2. 0 full speed MP3 (*. mp3) FAT12, FAT16, FAT32 The left and right speakers are the same. You cannot remove the net of the speakers. You can cause damage to the system and decrease the sound quality if you use other speakers. Note: • Keep your speakers more than 10 mm from the main unit for ventilation. • Put the speakers on a flat safe surface. • These speakers do not have magnetic shielding. Do not put them near TVs, PCs or other equipment easily influenced by magnetism. • When you play at high levels for a long period, it can cause damage to the speakers and decrease the life of the speakers. • Decrease the volume in these conditions to prevent damage: – When the sound is distorted. – When you adjust the sound quality. • Use the speakers only with the recommended Red Black Be careful not to cross (short-circuit) or reverse the polarity of the speaker wires as doing so may damage the speakers. (6 ) (6 ) CAUTION! system. If not, you can cause damage to the amplifier and speakers and can cause a fire. [. . . ] Press [R, T] to select a preset number and then press [OK]. Do steps 3 through 5 again to preset more stations. The new station replaces any station that occupies the same preset number. Press [PLAY MENU] repeatedly to select “SIGNAL QUALITY” and then press [OK]. The frequency block followed by the reception quality is shown. [. . . ]