User manual PANASONIC SC-PT550

[. . . ] The angles in the diagram are approximate. Main unit 1 FRONT (L, R) 2 SURROUND (L, R) 3 CENTER 4 SUBWOOFER Do not use a front speaker as a surround speaker or vice versa. Verify the type of speaker with the label on the rear of the front speaker. 1 FRONT (L, R) 2 FRONT (L, R) 3 CENTER 4 SUBWOOFER Main unit RQT8043 RQTX0043 3 Placement of speakers (continued) · Use only supplied speakers Using other speakers can damage the unit, and sound quality will be negatively affected. · Place speakers on flat secure bases. Take proper precautions to prevent the speakers from falling if you cannot set them up on an even surface. [. . . ] · English · Español · Français · Polski · Deutsch · Svenska · Italiano · Nederlands · Standard (Direct View TV) · CRT Projector · LCD TV/Projector · Projection TV · Plasma TV · 4:3 : Regular aspect television · 16:9: Widescreen television · Video/YPbPr · RGB/No Output · S-Video/YPbPr · Boxed items in the above table are the factory preset. RQT8043 RQTX0043 5 Speaker assembly Preparation · To prevent damage or scratches, lay down a soft cloth and perform assembly on it. · For assembly, use a Phillips-head screwdriver. · There is no difference between the right and left speakers and stands. · For optional wall mount (\ page 7). Make sure you have all the indicated components before starting assembly, setup, and connection. 2 Front speakers 2 Stands (with cable) 2 Bases 8 Screws 4 Stands 4 Bases 16 Screws 2 Front speakers and · 2 x stands with short cable: For 2 Surround front speakers speakers · 2 x stands with long cable: For surround speakers 1 2 4 1 3Tighten securely. 5 Slide into the groove. 2 4Insert the wire fully. +: White -: Blue 2 2 1 Position the cable between the ridges. Push! Leave about 80 mm 5Press into the groove. 3Tighten securely. 1 Speaker assembly option Thread the speaker cable through the base. Leave about 100 mm Push! Attach the speaker. 2Insert the wire fully. +: White -: Blue 3Press into the groove. You can remove and use the cable from the stand. To reattach the cable (\ page 7). 1Tighten securely. 6 RQT8043 7 Preventing the speakers from falling · You will need to obtain the appropriate screw eyes to match the walls or pillars to which they are going to be fastened. · Consult a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that may not have strong enough support. Improper attachment may result in damage to the wall or speakers. String (not included) Thread from the wall to the speaker and tie tightly. 150 mm Screw eye (not included) Wall RQTX0043 Rear of the speaker Speaker installation options 7 Attaching to a wall You can attach all of the speakers (except subwoofer) to a wall. · The wall or pillar on which the speakers are to be attached should be capable of supporting 10 k per screw. Consult a qualified building contractor when attaching the speakers to a wall. Improper attachment may result in damage to the wall and speakers. 1 Drive the screw (not included) into the wall At least 30 mm 2 Fit the speaker securely onto the screw(s) with the hole(s) * Front/Surround speakers Attach to a wall without the base and stand. Center speaker Ø4. 0 mm Wall or pillar Ø7. 0 to 9. 4 mm 4. 0 to 6. 0 mm 190 mm Surround speaker 384 mm * For For : Front and Surround speakers : Front speakers 7 Fitting speaker stands (not included) (For center and satellite surround speakers) Ensure the stands meet these conditions before purchasing them. Note the diameter and length of the screws and the distance between screws as shown in the diagram. · The stands must be able to support over 10 k . · The stands must be stable even if the speakers are in a high position. Example: Center speaker Metal screw holes For attaching to speaker stands 5 mm, pitch 0. 8 mm Plate thickness plus 7 mm to 10 mm 60 mm Speaker stand (not included) 7 Reattach the speaker cable 1 Insert the cable from the bottom. 2 Pull out the cable through the hole. RQT8043 RQTX0043 Leave about 80 mm 7 Operating other equipment Optional antenna connection Use the outdoor antenna if radio reception is poor. [. . . ] · The description of the component video input terminals depends on the television or monitor (example: Y/PB/PR, Y/B-Y/R-Y, Y/CB/CR). · Connect to terminals of the same color. HDMI cable (not included) Use the HDMI connection to enjoy higher quality audio and video with a single cable. · Set "Video Mode" to "On" and "Audio Output" to "On" (\ page 29, "HDMI" tab, Operations Guide). · Set "Video Output Mode" (\ page 24, Picture Menu, Operations Guide). [. . . ]