User manual PANASONIC SCSP100EB

[. . . ] If this occurs, immediately disconnect the unit from the power supply and contact your dealer. Do not spray insecticides onto or into the unit. They contain flammable gases which can ignite if sprayed into the unit. Voltage Do not use high voltage power sources. This can overload the unit and cause a fire. [. . . ] 13 Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 M12 (for iPhone) (RFEX1001) (RFEAX1003) 1 Audio cable 6 RQTX1010 M15 (for iPhone 3G) (RFEX1002) (130-318030003) Preparing the remote control Before using the remote control for the first time, remove the insulation sheet. Replace the remote control battery when it stops operating, or when the range seems reduced. Rear view 1 Insert an object and push down to unlock the catch. · Do not heat or expose to flame. · Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period of time with doors and windows closed. · Remove the battery if the remote control is not going to be used for a long period of time. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Warning Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 60°C or incinerate. Lithium Button-Type battery (CR2025) CR 20 25 Pull RQTX1010 Aim at the remote control signal sensor (\ page 10), avoiding obstacles, at a maximum range of 7 m directly in front of the main unit. 7 Compatible iPod and iPhone · iPhone 3G (8GB, 16GB) · iPhone (4GB, 8GB, 16GB) · iPod touch 2nd generation (8GB, 16GB, 32GB) · iPod nano 4th generation (video) (8GB, 16GB) · iPod classic (120GB) · iPod touch 1st generation (8GB, 16GB, 32GB) · iPod nano 3rd generation (video) (4GB, 8GB) · iPod classic (80GB, 160GB) · iPod nano 2nd generation (aluminum) (2GB, 4GB, 8GB) · iPod 5th generation (video) (60GB, 80GB) · iPod 5th generation (video) (30GB) · iPod nano 1st generation (1GB, 2GB, 4GB) · iPod 4th generation (colour display) (40GB, 60GB) · iPod 4th generation (colour display) (20GB, 30GB) · iPod 4th generation (40GB) · iPod 4th generation (20GB) · iPod mini (4GB, 6GB) Compatibility depends on the software version of your iPod or iPhone. Charging the iPod or iPhone · The iPod or iPhone charges automatically when power is supplied to the main unit. · Check iPod or iPhone to see if the battery is fully recharged. · If you are not using the iPod or iPhone for an extended period of time after recharging has completed, disconnect it from the main unit, as the battery will be depleted naturally. (Once fully recharged, additional recharging will not occur. ) 8 RQTX1010 Connecting the iPod or iPhone 1 Connect the AC power. Rear view AC mains lead (included) 2 Insert the dock adaptor into the main unit. iPod Use the adaptor supplied with your iPod or refer to Apple Inc. for the compatible dock adaptor (for details, refer to the instructions supplied with the dock adaptors), which may need to be purchased separately. AC adaptor (switching power supply) (included) iPhone To household mains socket Use an appropriate iPhone adaptor when playing an iPhone. The AC adaptor (switching power supply) is in the standby condition when the mains plug is connected. The primary circuit is always "live" as long as the mains plug is connected to an electrical outlet. Note: · The included AC mains lead is for use with this unit only. · Do not use an AC mains lead from other equipment. · Do not use any other AC adaptors (switching power supplies) except the supplied one. 3 Connect the iPod or iPhone to the main unit. Hold the main unit when connecting or disconnecting the iPod or iPhone. iPod (not included) iPod dock adaptor (not included) When removing, insert your fingernail or a flat object and lift upwards. RQTX1010 9 Listening to the iPod or iPhone Main unit Remote control signal sensor Power indicator You can navigate the iPod or iPhone using the buttons described. The power indicator blinks each time a button on the remote control is pressed. [. . . ] · The iPod or iPhone was incorrectly inserted into the dock. Turn off the iPod or iPhone, remove it from the dock connector. · Ensure the iPod or iPhone is seated properly into the unit. · Set the "EQ" setting of the iPod to "Off" or "Flat". [. . . ]