User manual PANASONIC SH-MZ1200

[. . . ] Operating Instructions DJ Mixer Model No. SH-MZ1200 The photograph shows the silver model. Note: "EB" on the packaging indicates the United Kingdom. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. EB EP GN RQT7231-B Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Supplied accessories Please check and identify the supplied accessories. [. . . ] If this occurs, immediately disconnect the unit from the power supply and contact your dealer. Do not spray insecticides onto or into the unit. They contain flammable gases which can ignite if sprayed into the unit. Service Do not attempt to repair this unit by yourself. If sound is interrupted, indicators fail to light, smoke appears, or any other problem that is not covered in these operating instructions occurs, disconnect the AC mains lead and contact your dealer or an authorized service center. Electric shock or damage to the unit can occur if the unit is repaired, disassembled or reconstructed by unqualified persons. Extend operating life by disconnecting the unit from the power source if it is not to be used for a long time. Providing new audio performance using the channel fader and cross fader Use the channel fader to control the left (L) and right (R) channels individually ·With the PLAY MODE function the selected channels can be separated and the L or R volume can be controlled individually using the channel fader. Control the FRONT and REAR output for two channel output using master 1, 2 ·By turning the SEPARATE OUT switch to on, you can separate CH1 and CH2 output to the front and CH3 and CH4 output to the rear, providing you with new sound field performance in combination with the feature of being able to adjust the left (L) and right (R) channels individually. Insertion of connector Even when the connector is perfectly inserted, depending on the type of inlet used, the front part of the connector may jut out as shown in the drawing. However there is no problem using the unit. Connector Approx. 6 mm Appliance inlet Linked play on the connected digital turntable Real-time start and stop control using the fader ·You start and stop the digital turntable by operating the channel fader or cross fader when connected to a digital turntable with a control cable. Curve switch (CURVE) Cross fader operation switch (CROSS FADER) Fader operation switch (CH1-CH4 FADER) . . . . . . . . . . Headphone terminal (PHONES) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fader start (ON, OFF) switch (FADER START) . . . . . Power button (POWER OFF ON) . . . . . . . . . . . . . . . . . . . Turntable earth terminal (PHONO EARTH) . . . . . . . . . . . Input terminal (CH1-CH4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CD/LINE: CD or line terminal LINE: Line terminal PHONO 1-3: Turntable phono terminal Microphone input terminal (MIC1, MIC2) . . . . . . . . . . . . . . Effector input-output terminal (EFFECT RETURN, EFFECT SEND) . . . . . . . . . . . . . . . . . . . . . . Player control (CH1, CH4) terminal (PLAYER CONTROL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital output terminal (DIGITAL OUT) . . . . . . . . . . . . . . . . . . Digital input (CH1, CH4) terminal (DIGITAL IN) . . . . Output terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Master out 1, 2 terminal (MASTER OUT) Monitor out terminal (MONITOR OUT) Rec terminal (REC OUT) Power input terminal (AC IN ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 RQT7231 Connections Output side connections Connect the various equipment to the DJ mixer using stereo phono cables, connection cables and appropriate cables (Each sold separately). When connecting, make sure to turn all equipment power off. Stereo phono cables Speakers (Not included) White (L) Red (R) Speakers (Not included) Speakers (Not included) Amplifier (Not included) Amplifier (Not included) Monitor amplifier (Not included) Rear panel Connect when using an amplifier that has XLR terminals. Terminal polarity is indicated in the diagram below. [. . . ] Have you connected with the left and right terminals reversed?Is there a fluorescent light or other electrical appliances, or are their power cables near any of the connecting cables?Has the turntable's grounding wire been disconnected?Is the master volume level or monitor volume level too high? [. . . ]