User manual PANASONIC SL-SX390

[. . . ] Concerning Compact Discs Only compact discs bearing this mark can be used with this unit. However, continued use of irregular shaped CDs can damage the unit. Portable CD player Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. The model number and serial number of this product can be found on either the back or the bottom of the unit. [. . . ] (The numbers of the programmed tracks appear on the display in sequence. ) To delete the entire programmed sequence Press []. Note! The setting returns to S-XBS when you disconnect the power source. Note! The repeat and random play modes are canceled after steps 1 and 2. Anti-Skip System This system deals with skipping in a variety of ways: An anti-skip mechanism prevents skipping caused when play speed changes due to swinging of the unit. A recovery system immediately returns the laser pickup to its original position if it is knocked off the track by a strong shock. 48seconds) fills in interruptions caused by bumps and vibrations. The anti-skip system works automatically while the system is on and cannot be canceled. When bumps continue repeatedly The elapsed playing time disappears and sound is interrupted. S-XBS TRAIN RANDOM 1 M Note! While the system is on, the disc rotates at a higher rate than usual in collecting extra audio data. This could result in a slight increase in disc rotation noise. The anti-skip memory compresses digital signals. E C VOL 4 Using the Wired Remote Control The remote control can be operated regardless of the HOLD mode of the unit. Basic operation Press once during off or stop mode. VOL Preparation: Release the remote control from the HOLD mode. EQ HOLD Press during play. Skipping tracks (Press [:] twice to skip to the beginning of the previous tracks. ) Backward (Beep Beep Beep) VOL To start play (Beep) HOLD To stop play Press once during play. VOL Searching through tracks Forward (Beep Beep) Operation confirmation tones » When an operation button is pressed, a confirmation tone sounds. Refer to the parentheses in the illustration for the different types of confirmation tones. Press and hold during play. (Beep. . . Beep) VOL Turning the operation tones off and on » While stopped or during play » Press and hold [EQ] on the remote control for 5 seconds until the unit's display appears. The tone sounds when the setting is changed. Press and hold during play or stop mode. To turn off the unit VOL To adjust the volume Decrease (Beep) VOL Increase (Beep) (Beep. . . Bee. . . p) The volume range is 0­25. (Press and hold to change the volume successively. ) A tone (beep-beep) sounds when you reach the minimum or maximum volume. EQ HOLD EQ Changing the sound quality (Beep) Press during play or stop mode. EQ The setting switches in the sequence indicated below each time [EQ] is pressed. S-XBS>TRAIN>Cancel (no indicator is shown) To turn the tone off To turn the tone on EQ HOLD ^==========b S-XBS: Select this setting to boost the low-range response. TRAIN: Select this setting to avoid annoying other passengers with noise from your headphones/earphones while riding on the train, or to reduce fatigue when listening for a long period of time. Note! The setting returns to S-XBS when you disconnect the power source. Using the Unit with Optional Accessories Using the unit with an audio system Turn off this unit and the other equipment before connection. 1 Connect the remote control to [Ë] on the unit. 2 Connect the stereo connection cable to the remote control and the other equipment. The unit may malfunction if you connect directly to [Ë] on the unit. Do not connect the cable to the PHONO jacks on the amplifier. 3 Turn the operation tones off (see above) so they are not heard when you press buttons on the remote control. Make further volume adjustments with the other equipment. Using the unit with a car audio system Headphone jack (Ë) Items to be purchased For connection to the car audio system Car stereo cassette adaptor (SH-CDM10A) Connect the car stereo cassette adaptor to [Ë] on the unit. (When doing this, set this unit's volume to 10. ) For securing the unit and connecting the power supply: Car adaptor (SH-CDC9) Car mounting kit (SH-CDF20) Note when using the car mounting kit (SH-CDF20) 1Remove the screw from Bracket the bracket at the rear of the car mounting base. 2Replace the screw in the lower hole of the bracket. Screwdriver VOL EQ MEM ORY /RECAL L MODE Other equipment HO LD OPEN (White) L To CD or AUX (Red) R terminals Note! Obtain the optional connecting cable if the other equipment comes with mini-phone jacks. If you connect speakers (active or otherwise) directly to the unit's headphone jack, ensure they have an impedance of 1 k or less. VOL Stereo connection cable (not included) Note! When you switch off the car, volume and sound quality may return to the original settings and the resume function may work even if you change the disc. [. . . ] Do not peel off the covering on batteries and do not use if the covering has been peeled off. Align the poles + and - correctly when inserting the batteries. Do not mix different types of batteries or old and new batteries. Remove the batteries if you do not intend to use the unit for a long time. [. . . ]