User manual PANASONIC SP3220UV

[. . . ] Later you may read this Manual and use it for further reference. TABLE OF CONTENTS D D D D D Warnings and Precautions . D Tuning --- Automatic Tuning Process (ATP) . 2 3 4 5 5 6 7 8 9 10 11 12 12 13 14 14 15 16 17 18 19 20 20 D D D D D WARNINGS AND PRECAUTIONS ` This television set is designed to be connected to an AC 220---240 V, 50 Hz power source. ` To avoid damage that may result in an electric shock or fire do not expose the unit to rain or excessive moisture. [. . . ] By pressing button "F" you either enter the on---screen indications menu or go back to another menu. By pressing button "N" you close either the on---screen menu or the selected parameter. Button "TV/AV" is normally used to confirm the selection. 5 MAIN MENU This section shows among others how to adjust the picture quality. Press button "F" Select the required parameter Main Menu Increase or decrease the level. Contrast Brightness Colour Sharpness Tint (NTSC only) Off timer Sound Menu Setup Menu Select Adjust Exit Press button "N" to leave the menu. Off The level of contrast, brightness, colour and sharpness may be Brightness adjusted so as to meet the requirements of your sight. You may the level by the Colour go back to at any time set pressing manufacturer by button "N". Contrast Contrast Sharpness The line "Tint" will appear as a menu line only when a NTSC signal is Tint connected to the unit via the AV input thus allowing the tints to be adjusted. Switches off your television at the time you set from 0 to 90 minutes with 15---minute intervals. The Sound menu allows you to adjust the sound as you wish. The Setup menu provides access to various advanced features and also to the Tuning menu. Off timer Sound menu Setup menu 6 SOUND MENU This section shows how to adjust the sound as you wish. Press button "F". Select Sound menu Select Access Enter Sound menu Main Menu Contrast Brightness Colour Sharpness Tint (NTSC only) Off timer Setup Menu Exit Select the required parameter Sound Menu Adjust the level and confirm the selection Leave the menu by pressing button "N" Access Off Select Adjust Sound menu Parameter Volume adjusts the level of the Volume input sound Parameter Bass adjusts lower Bass to enhance or diminish them. frequencies Volume Bass Return Exit Treble Stereo Music Balance MPX Mode Treble frequencies to enhance or diminish them. Balance Parameter Treble adjusts higher Balance adjusts the sound level between the left and right speakers. To tune in to other programmes, repeat the above procedure or finish the tuning by pressing button "F". ---/ +/ STR Notes: If you know the channel numbers of your broadcasting stations you may use direct channel selection by using button "C" on the remote control unit to save the channels quickly: --- enter Manual menu; --- pre---set the programme number; --- press button "C"; --- set the channel number with the numbered buttons; --- save with button TV/AV; --- leave the menu by pressing button "N". If you want to use direct channel selection in the "Hyperband" (cable TV), press the direct channel selection button and programme position button ("C" and "---/--- ---") one after the other and set the number with the numbered buttons. "CH--- ---" will first appear in the left top corner of the screen, and then "H:--- ---". For saving see above. F 11 SWAP The Swap option allows you to swap between two programme positions. Press button "F". Select first programme position. Prog with Prog 01 02 CH44 CH41 BBC1 ITV Select Adjust Return Swap Exit Select second programme position. Confirm with button "TV/AV". Leave menu by pressing button "N". OSD LANGUAGE When first setting up your television, select the OSD language to match your country selection. If you want to use another language you may select the language from the language menu. Press button "F". Select Setup menu. Select Select Return Exit Enter Setup menu. Save and leave the menu by pressing button "N". Deutsch English Français Italiano ELLHNIKA Español Norsk Dansk Svenska Nederlands Suomi Türkçe Português 12 Q ---LINK The Q---Link function transmits the data from the television to the VCR. Press button "F". Select Setup menu. Return Select Access Exit Enter Setup menu. Leave the menu by pressing button "N". Setup Menu Text Language Aspect C --- A --- T --- S Colour system (AV only) West Auto AUTO Q --- Link Tuning Menu OSD Language On Access The VCR must be connected with a (full) SCART cable to the AV1 jack and the appropriate jack on the VCR. See the VCR Operation Manual for more detailed information. [. . . ] Programme Number Up And Down By pressing these buttons the programme number will be increased or decreased by one position. REC Record Press this button to start recording. DIRECT TV REC Direct TV Record Press this button to start recording directly from the television. See page 13. 15 TELETEXT FUNCTION D Teletext functions may vary depending on the broadcasting companies and are only available if the selected channel is transmitting Teletext. D If button "F" is pressed in the Teletext mode the blue contrast scale will appear; press buttons "+" and "---" to change the settings. D When in Teletext mode, the volume may still be adjusted by pressing buttons "+" or "---". What is FLOF (FASTEXT)? In the FASTEXT mode four differently coloured subjects are shown at the bottom of the screen matching the colour of the buttons on your remote control unit. To access more information about one of these subjects, press the appropriately coloured button. This function allows quick access to information on the subject shown. TV/TEXT TV/Teletext Mode Press button TV/TEXT. [. . . ]