User manual PANASONIC SP3229V

[. . . ] Retain your purchase receipt also, and note down the Model Number and Serial Number of your set in the space provided on the rear cover of these Instructions. AR/AS Coating on the Screen ( for SP3229V, TC-51P100H ) The Screen is coated with a special material to hinder ambient light reflection and dust adherence. It aids picture performance during high ambient light conditions. The AR/AS coating may be observed when the set is switched off, since the coating give the screen surface a faint purplish or blue hue. Take care not to mark or scratch this coating. Important Information (1) The long time (max. [. . . ] (2) If a clear picture with correct colours cannot be obtained when a Broadcast or AV signal is received, refer to the "Colour System Selection" operation on page 35. (3) After the Automatic tune is finished, push the Programme Number "" button to confirm the tuning condition for each Programme Number. If some Programme Numbers are unused, it is possible to skip such Programme Numbers. Please refer to the Programme Number Skip operation on page 30. (4) Repeated pushing of the "PRE. " (PRESET) button changes the Preset Menu as follows; CH SELECT (Page 21) SYS SELECT (Page 22) AUTO TUNE (Page 24) MANUAL TUNE (Page 26) (Page 35) SOUND SYS (Page 34) TV Mode (Normal viewing condition) SKIP (Page 30) FINE TUNE (Page 28) COLOUR SYS 25 Tuning Procedure Manual Tune (Channel Select and Regional System must already be set; Refer to pages 20 to 23) 1, 4, 6 3, 5 2 DISPLAY TV/AV PRE. - + (TV set) 1 PRE. Push the "PRE. " (PRESET) button 4 times. 2 Push either the Programme Number Up "" or Down "" button. 3 + Push the Volume Up "+" or Down "-" button. Volume "+" : Next higher Channel Volume "-" : Next lower Channel 2 CH4 4 PRE. Push the "PRE. " (PRESET) button. 26 ^ 1 CH1 2 CH2 2 CH4 ^ GAME Manual Search "MANUAL TUNE" Condition. Select the desired Programme Number. Search Start. The best tuning position is automatically memorized. "SOUND SYS" Condition. Tuning Procedure 5 + If the sound is not clear or no sound is produced on a Programme Number Position, push the Volume Up "+" or Down "-" button. 2 CH4 Yo u m ay i m p r o ve t h e Sound quality. The sound indicator will change as follows. 4. 5MHz 6. 5MHz 5. 5MHz 6. 0MHz Note: When sound volume is too small to confirm, turn it up by using the sound volume button on the remote control. Push the "PRE. " (PRESET) button 4 times. PRE. 6 This returns the set to the normal viewing condition. Helpful Hint (1) If a clear picture cannot be obtained even when a Broadcast or AV signal is received, refer to the "Colour System Selection" operation on page 35. (2) After the Manual tune is finished, push the Programme Number "" button to confirm the tuning condition for each Programme Numbers. If some Programme Numbers are unused, it is possible to skip such Programme Numbers. Push the Display button a second time to halt the display/demonstration mode, and return the set to the normal viewing condition. Note: When this button is pushed, the Picture and Sound Menus change to Picture (DYNAMIC) and Sound (DYNAMIC). S-DYNAMIC P-DYNAMIC 30 Programme Number (Refer to page 20) Audio Mode (Refer to page 41) Sound Menu (Refer to page 43) Picture Menu (Refer to page 42) Off Timer (Refer to page 33) 7 GAME Game button Push this button to change to the AV2 input signal and enter Game mode. The picture and sound changes to a suitable mode for video games. Note: When you push this button during stand-by mode, the TV will turn on automatically and the picture and sound changes to a suitable mode for video games. 10 Off Timer button The TV set may be preset to switch to stand-by after a fixed period. By pushing "Off-Timer" button, you can select the preset time; either "30", "60", "90" minutes or AUTO mode. 30 60 0 90 AUTO 8 Sound Mute button Push this button to mute the sound completely. The "Mute" symbol will appear. (Colour change to red) Setting Off-Timer to AUTO mode. If the set is not switched off when the TV station stops broadcasting, it will automatically go to Stand-by mode after 5 minutes. Note: Off-Timer setting will not operate in AUTO mode when the Television set is in AV mode. Push the button once again to restore the previous sound level, and cancel the mute. 33 General Operation Sound System Selection (Different region use differing systems) 1, 3 2 DISPLAY TV/AV PRE. - + (TV set) This function is used only in the TV mode, and is not applicable in AV mode when the sound is not clear or no sound is produced on a Programme Number. 1 PRE. Push the "PRE. " (PRESET) button 5 times. 2 CH2 2 + Push the Volume Up "+" or Down "-" button repeatedly until the optimum sound is obtained. 2 CH2 3 PRE. Push the "PRE. " (PRESET) button 4 times. 34 ^ ^ GAME Sound System Condition. The sound system will change as shown. 4. 5MHz 6. 5MHz 5. 5MHz 6. 0MHz Note: These are different sound broadcast transmission systems applicable to differing countries. This returns the set to the normal viewing condition. The selected Sound System is automatically memorised. General Operation Colour System Selection (Different region use differing systems) 1, 3 2 DISPLAY TV/AV PRE. - + (TV set) If a clear picture with current colours cannot be obtained when a Broadcast or AV signal is received. 1 PRE. Push the "PRE. " (PRESET) button 6 times. [. . . ] News Flash When a news flash page has been selected, push Position Left "<" or Right ">" button to view the TV picture, when an update is received, it will be displayed on screen. Update Push Position Left "<" or Right ">" button to see the update of information on certain pages. When an update is received, the page number will be displayed at the top left of the screen. LIST STORE In LIST mode the four page numbers can be altered for channel position. To do this, push one of the colour coded buttons and enter the new page number. [. . . ]