User manual PANASONIC SU-A600MK2

[. . . ] The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Batteries or batteries installed apparatus shall not be exposed to excessive heat such as sunshine, fire or the like. [. . . ] When you turn on the connected components, the system and the TV are also turned on, and the input source changes automatically. You can also adjust the system's volume using the TV's remote. For details on setting "BRAVIA" Sync, see "Preparing for "BRAVIA" Sync" (page 38). Tip TUNER AM* The built-in AM radio * Press TUNER repeatedly to switch between TUNER FM and TUNER AM. 4 For video components, change the TV's input to the HDMI input you chose in step 3. For details, refer to the operating instructions of your TV. · The system is not turned on when you turn the TV on if sound was being output from the TV speakers the last time the TV was turned off. 5 Tips Adjust the volume by pressing 2 +/­. · The sound may be output from the TV's speaker. In this case, turn the volume of the TV's speaker down to minimum. · Even if you playback Dolby True HD, Dolby Digital Plus or DTS HD with a connected component compatible with these sound formats, the system accepts the signal as Dolby Digital or DTS. When you playback these high-quality sound formats, set the connected component to output the sound in multichannel PCM, if possible. 31GB 3 Tuner Functions While pressing and holding SHIFT (1), press the number buttons (2) to enter the frequency. Direct tuning You can enter the frequency of a station directly using the number buttons. Example: 88. 00 MHz While pressing and holding SHIFT, select 8 t 8 t 0 t 0. Number buttons TUNER ENTER D. TUNING 4 Tip While pressing and holding SHIFT, press ENTER. · If you have tuned in an AM station, adjust the direction of the AM loop antenna (aerial) for optimum reception. If you cannot tune in a station Make sure you have entered the right frequency. If you still cannot tune in a station, it is likely that the frequency is not used in your area. SHIFT 1 2 Press TUNER repeatedly until "TUNER FM" or "TUNER AM" appears in the front panel display. Press D. TUNING. 32GB Presetting radio stations You can preset 20 FM and 10 AM stations. Before tuning, make sure to turn down the volume to minimum. 5 Press . "COMPLETE" appears in the front panel display, and the station is stored. 6 Repeat 2 to 5 to store other stations. Tuner Functions To change the preset number Restart from step 3. Listening to the radio TUNER Preset radio stations in the system's memory first (see "Presetting radio stations" (page 33)). MEMORY ?/1 C, X, x, c, TUNER TUNING +/­ 1 2 Press TUNER repeatedly until "TUNER FM" or "TUNER AM" appears in the front panel display. Press and hold TUNING +/­ until the auto scanning starts. C, X, x, c, MENU Scanning stops when the system tunes in a station. "TUNED" and "ST" (for FM stereo program) light up in the front panel display. TUNING +/­ PRESET +/­ 3 4 Press MEMORY. 2 +/­ A preset number appears in the front panel display. Press X/x to select the preset number you want. 1 Press TUNER repeatedly until "TUNER FM" or "TUNER AM" appears in the front panel display. The last received station is tuned in. continued 33GB 2 Press PRESET +/­ repeatedly to select the preset station. Naming preset stations You can enter a name for preset stations. Suited for music programs or music videos on Blu-ray Discs/DVDs. Suited to replay portable audio source. Surround Function GAME* MUSIC* 2CH STEREO Suited for music CDs. P. AUDIO** SOUND FIELD +/­ * These sound fields are not available when "DMPORT" is selected by pressing INPUT SELECTOR. ** "P. AUDIO" appears only when "DMPORT" is selected. Tips Press SOUND FIELD +/­. The present sound field appears in the front panel display. Each time you press SOUND FIELD +/­, the display changes cyclically as follows: STANDARD y MOVIE y DRAMA y NEWS y SPORTS y GAME y MUSIC y 2CH STEREO y P. AUDIO y STANDARD . . . · You can set a different sound field for each input source. · The sound field default setting for "DMPORT" is "P. AUDIO, " and for other sources, "STANDARD. " · When "DMPORT" is selected by pressing INPUT SELECTOR, the center speaker produces no sound. · Some speakers will not produce sound depending on the input signal, such as monaural programs. · When "2CH STEREO" or "P. AUDIO" is selected, the center speaker produces no sound. · If you press the THEATRE button on a Sony TV remote when "CTRL HDMI" is set to "ON, " the sound field changes to "MOVIE" (some Sony TVs excluded). 37GB "BRAVIA" Sync Features What is "BRAVIA" Sync? By connecting Sony components that are compatible with "BRAVIA" Sync via an HDMI cable (not supplied), operation is simplified as below: · One-Touch Play (page 39) · System Audio Control (page 40) · System Power Off (page 41) "BRAVIA" Sync is compatible with Sony TVs, Blu-Ray Disc/DVD players, AV amplifiers, etc. , with the Control for HDMI function. CONTROL FOR HDMI is a mutual control function standard used by CEC (Consumer Electronics Control) for HDMI (High-Definition Multimedia Interface). Preparing for "BRAVIA" Sync To use "BRAVIA" Sync, set the Control for HDMI function to on for the connected components. When you connect a Sony TV with the Control for HDMI function, the Control for HDMI function for the system and the connected components can be set simultaneously by setting the Control for HDMI function of the TV. ?/1 The Control for HDMI function will not operate correctly in the following cases: · When you connect the system to components which do not correspond with the Control for HDMI function. · When you connect the system and components using other than an HDMI connection. [. . . ] · Check that all the cables and cords of the system and the connected components are fully inserted. · Check the HDMI setting of the connected components. No sound is output from specific speakers. · Check that the connectors of the speaker cord are fully inserted into the jacks. · Depending on the sound source that is input to the system or selected sound field of the system (page 37), no sound is output from the center speaker. Sound is interrupted or there is noise. · "CTRL HDMI" is set to "OFF. " · When the system is in standby mode, image and sound are output from the HDMI component selected the last time you turned off the system. If you want to play a component other than the HDMI component you selected last time, play the component via One-Touch Play, or turn on the system to select the HDMI component you want to enjoy. [. . . ]