User manual PANASONIC SUC700AEB

[. . . ] SU-C700_SQTxxxx_EB_EBGN_mst. book 1 ページ ２０１５年６月１２日　金曜日　午後４時４分 Operating Instructions Stereo Integrated Amplifier SU-C700A SU-C700_SQTxxxx_EB_EBGN_mst. book 2 ページ ２０１５年６月１２日　金曜日　午後４時４分 SU-C700_SQTxxxx_EB_EBGN_mst. book 3 ページ ２０１５年６月１２日　金曜日　午後４時４分 Music is borderless and timeless, touching people’s hearts across cultures and generations. Each day the discovery of a truly emotive experience from an unencountered sound awaits. Let us take you on your journey to rediscover music. SU-C700_SQTxxxx_EB_EBGN_mst. book 4 ページ ２０１５年６月１２日　金曜日　午後４時４分 Thank you for purchasing this product. Please read these instructions carefully before using this product, and save this manual for future use. [. . . ] Clean this unit with a soft cloth. ≥ When dirt is heavy, wring a wet cloth tightly to wipe the dirt, and then wipe it with a soft cloth. ≥ Do not use solvents including benzine, thinner, alcohol, kitchen detergent, a chemical wiper, etc. This might cause the exterior case to be deformed or the coating to come off. 6 SU-C700_SQTxxxx_EB_EBGN_mst. book 7 ページ ２０１５年６月１２日　金曜日　午後４時４分 Control reference guide SB-C700AST-C700A This unit ∫ Front       ∫ Rear       1 Power switch lever Turn on/off this unit.       9 PHONO EARTH terminal [PHONO EARTH] ( 11) For connecting the ground wire of a record player. : Analogue audio input terminal [PHONO] ( For connecting a record player. ≥ MM cartridges are supported. ≥ The remote control do not operate when the power switch lever is in the lowered position. 11) 2 Headphones jack For connecting a headphone plug. ≥ When a plug is connected, the speakers do not output sound. ≥ Excessive sound pressure from earphones and headphones can cause hearing loss. ≥ Listening at full volume for long periods may damage the user’s ears. ; Attenuator [ATTENUATOR] If audio distortion occurs when using the analogue audio input terminal [LINE IN], set this switch to [ON]. < Analogue audio input terminal [LINE IN] ( = Speaker terminals [SPEAKERS] ( > AC IN terminal [AC IN T] ( 12) 15) 11) 10, 11) 10) ?Digital audio input terminal [PC] ( For connecting to a PC, etc. 9) 11) 3 LAPC indicator ( 13) The indicator lights up when amplifier output correction is on. 4 Volume knob Adjust the volume. ≥ When this unit is muted, if you turn the knob anticlockwise until it stops and then turn it clockwise, the muting will be cancelled. @ Digital audio input terminal [OPT IN] ( A Digital audio input terminals [COAX1 IN]/[COAX2 IN]/[COAX3 IN] ( C Product identification marking The model number is indicated. 5 Remote control signal sensor Distance: Within approx. 30o left and right 6 Input selector knob Turn this knob clockwise or anticlockwise to switch the input source. ( 13) 7 Peak power meter Display the output level. 8 Input indicator ( 13) The indicator for the selected input source lights up. ≥ The indicator blinks if you select “PC”, “COAX1”, “COAX2”, “COAX3” or “OPT” when the device is not connected to this unit. B System terminals [CONTROL1]/[CONTROL2] ( 7 SU-C700_SQTxxxx_EB_EBGN_mst. book 8 ページ ２０１５年６月１２日　金曜日　午後４時４分 Remote control ∫ Buttons that work for this unit      1 [AMP Í]: Standby/on switch Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. ≥ The remote control do not operate when the power switch lever is in the lowered position. 2 [AMP]/[NWP]/[CD]: Select the device to be operated [AMP] [NWP] [CD] LINE indicator lights up COAX1 indicator lights up COAX2 indicator lights up 13)       3 [N INPUT O]: Select the input source ( 4 [DIMMER]: Adjust the brightness of the light and the indicators Each press of this button switches the brightness. 5 [LAPC]: Measure the characteristics of the amplifier and correct its output ( 13) 6 [r VOL s]: Adjust the volume 7 [MUTE]: Mute the sound Input indicator blinks. ≥ You can automatically link this unit with the ST-C700A/SL-C700 and operate them easily with the remote control. ( SL-C700 System connection cable System connection cable 14) ST-C700A This unit (rear) Coaxial digital cable Coaxial digital cable ≥ Use the system connection cables and the coaxial digital cables supplied with the ST-C700A/SL-C700. ≥ Connect the system connection cables to the system terminals [CONTROL1]/[CONTROL2]. Connect the ST-C700A to [CONTROL1] and the SL-C700 to [CONTROL2]. ≥ Connect coaxial digital cables to the digital audio input terminals [COAX1 IN]/[COAX2 IN]. Connect the ST-C700A to [COAX1 IN] and the SL-C700 to [COAX2 IN]. 10 SU-C700_SQTxxxx_EB_EBGN_mst. book 11 ページ ２０１５年６月１２日　金曜日　午後４時４分 Connecting to analogue audio output devices You can input analogue audio signals to this unit and play back music. e. g. , Record player*1 This unit (rear) Blu-ray Disc player, etc. *2 Audio cable (not supplied) Audio cable (not supplied) *1 When connecting to a record player with a built-in PHONO equaliser, connect its cable to the analogue audio input terminal [LINE IN]. [. . . ] Connect the ST-C700A to [COAX1 IN] and the SL-C700 to [COAX2 IN]. A “humming” sound can be heard during playback. ≥ An AC mains lead or fluorescent light is near the cables. Keep other appliances and cords away from the cables of this unit. ≥ Set the [ATTENUATOR] switch to [ON]. ( 7) ≥ A strong magnetic field near a TV or other device may adversely affect the audio quality. [. . . ]