User manual PANASONIC SUZT1

[. . . ] Home Theater Audio System Model No. Operating Instructions SC-ZT1 If you have any questions contact In the U. S. A. and Puerto Rico: 1-800-211-PANA(7262) In Canada: 1-800-561-5505 For U. S. A. and Puerto Rico only The warranty can be found on page 30. For Canada only The warranty can be found on page 31. Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. [. . . ] Press and hold [­SETUP, OFF] for about 2 seconds. The setting items are displayed. Press [w][q] to select "DISTANCE " and press [OK]. Press [w][q] to select a speaker to set and press [OK]. Press [e][r] to select the distance and press [OK]. Functions and settings Adjustment range: 1. 0 to 10. 0 meter (3. 0 to 30. 0 ft (feet)) Factory setting : Front 3. 0 meter (10. 0 ft (feet)) Surround 1. 5 meter (5. 0 ft (feet)) FRONT : Front speakers SURR : Surround speakers 5. Press [ RETURN] several times to select "EXIT " and press [OK] to finish the setting. Note Radio waves from this system reach the maximum range of 15 m (49 feet) within the same room. Setting 7. 1-channel virtual surround When playing back 7. 1-channel LPCM signals, you can enjoy wider sound field effects as if another speaker is added. When you do not want to use 7. 1-channel virtual surround effect, select "OFF " in this setting. 1. Press and hold [­SETUP, OFF] for about 2 seconds. To return to the previous display/To cancel during setting operation: Press [ RETURN]. 2. Press [w][q] to select "7. 1CH VS " and press [OK]. Press [e][r] to select "OFF " and press [OK]. AUTO : The setting is switched between ON and OFF depending on the input signals. Only when 7. 1-channel LPCM signals are input, 7. 1-channel virtual surround is ON (When other signals are input, this setting is OFF. ). OFF : 7. 1-channel virtual surround is always OFF. Factory setting : AUTO The setting items are displayed. Press [ RETURN] several times to select "EXIT " and press [OK] to finish the setting. Reducing standby power consumption (In standby condition (HDMI off mode)) Standby through function ( pages 9, 28) does not work in this mode if you have connected through the HDMI terminal. VIERA Link "HDAVI Control" ( page 18) will not function when this system is off. 1. Press and hold [­SETUP, OFF] for about 2 seconds. Press [w][q] to select "HDMI " and press [OK]. Press [w][q] to select "STNBY " and press [OK]. Press [e][r] to select "OFF " and press [OK]. The setting items are displayed. Press [ RETURN] several times to select "EXIT " and press [OK] to finish the setting. 22 RQT9471 OFF : Standby power consumption reduced (approx. 0. 2 W) ON : "Standby through" is activated when this system is turned off. (Normal power consumption) Factory setting: ON VIERA Link "HDAVI Control" setting When you do not wish to use VIERA Link "HDAVI Control" ( page 18), you can set the unlinked operation by selecting "OFF ". [. . . ] · Do not use this device as a plaything. FCC Note: THE FOLLOWING APPLIES ONLY IN THE U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]