User manual PANASONIC SX-PR54

[. . . ] DIGITAL ENSEMBLE SX-PR54/M Operating Instructions Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. This manual was printed with soy based ink. ENGLISH QQTG0701 Caution for AC Mains Lead (For United Kingdom) (For the type as shown in figures A and B) For your safety, please read the following text carefully. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. [. . . ] Note that in some cases, the CONTROL, RHYTHM and CHORD part data in the destination tracks may be lost. Sequencer · If ALL is selected, the specified measures are copied to all tracks at the same time. FIRST MEAS: Specify the first measure to copy. LAST MEAS: Specify the last measure to copy. TRACK MERGE Merge the recorded contents of two tracks (source tracks) and store the merged contents in a third track (destination track). · When the TRACK MERGE function is executed, the data is erased from the two source tracks. 2. Specify where you wish to copy the selected measures to. · On the TO side, specify the settings with the corresponding buttons. TRACK: Specify the track number you wish to copy to. · Measures in a track for the CONTROL, RHYTHM or CHORD part can be copied only to the same track. 1. · On the FROM side, use the TRACK and buttons to START MEAS: Specify the start point to copy the selected measures to. REPEAT: Specify the number of times the selected measures are to be repeated. select the two source tracks. · You cannot select the track to which the CONTROL, RHYTHM or CHORD part has been assigned. · If the part assigned to the left source track ("left" meaning its position on the TRACK MERGE display) is different from the part assigned to the right source track, when the parts are merged in the destination track, the new track is assigned the same part as the left track. 3. Press the OK button. · The confirmation display appears. Press the YES button to execute the function, or press the NO button to cancel the function. · Note that if the END command is included in the source data, it is also copied. Any data following the END command is not copied. 2. · Use the TRACK and buttons to the right of the display to specify the track number. 3. Press the OK button. · The confirmation display appears. Press the YES button to execute the function, or press the NO button to cancel the function. MEASURE ERASE Erase the recorded contents of specific measures. You can also specify which type of data is to be erased. · Note that only the contents of the measures are erased, not the measures themselves; the length of the performance remains the same. Sequencer MEASURE COPY Copy recorded data of specified measures to a specified point. · On the destination track, the new data replaces the current measure contents. 1. Use the TRACK and buttons to specify the track number. · This function does not work for the RHYTHM part or CHORD part in which a repeat command has been stored. · If ALL is selected, data is erased from the specified measures of all the tracks at one time. 1. Specify the measures you wish to copy from the source track (FROM). · On the FROM side, specify the settings with the corresponding buttons. 2. Use the FIRST MEAS and buttons to specify the start point (measure number). TRACK: Specify the track number you wish to copy the measures from. · You cannot select the track for the RHYTHM part or CHORD part in which a repeat command has been stored. 3. Use the LAST MEAS and buttons to specify the end point (measure number). 76 QQTG0701 Part III 4. Use the ERASE DATA and buttons to specify the type of data to be erased. CONTROL: Only control data (volume, effect and other panel settings as well as selection changes) is erased. Sequencer MEASURE INSERT Insert specified measures at a specified point. · The length of the performance accordingly increases by the number of inserted measures. 5. [. . . ] Select MIDI. · The display looks similar to the following. MIDI 126 QQTG0701 (For U. S. A. ) PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA One Panasonic Way, Secaucus, New Jersey 07094 PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC. , Ave. 9. 5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 / Musical Instrument Products Limited Warranty Limited Warranty Coverage If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as "the warrantor") will, for the length of the period indicated on the chart below, which starts with the date of original purchase ("warranty period"), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor. Product Organs, Digital Pianos, Digital Ensemble Series, Tone Cabinets, Panasonic Digital Pianos Keyboards Panasonic Keyboards, Synthesizers, Sound Modules, Expansion Boards, Disk Drives, Drum Percussion Units, MIDI Orchestra, Keyboard Amplifiers, Foot Pedals, Foot Controllers, Personal Music PA Systems USB Reader/Writer, Personal Computer Card Adapters (in exchange for defective item) SD Memory Cards (in exchange for defective item) Parts Three (3) Years One (1) Year Labor One (1) Year One (1) Year Service In-Home or Carry-In In-Home or Carry-In In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized servicer and does not include removal or re-installation of an installed product. [. . . ]