User manual PANASONIC TC-202

[. . . ] EX: smoke, odd sounds or smells, turn the power switch off and disconnect the AC power if you notice any unusual operation. 2 Before Operating This Set Connect the Aerial Cable to the RF In Terminal VHF Aerial UHF Aerial Mixer 75 Coaxial Cable RF In Terminal Coaxial Aerial plug To obtain the best quality picture and sound, an external antenna, the correct cables (75 Ohm coaxial) and the correct terminating plug will be required. If a communal antenna system is used, you may require the correct connection cable and plugs between the wall antenna socket and your television receiver. Your local Television Service Dealer may be able to assist you in obtaining the correct antenna system for your particular area and accessories required. Any matters about antenna installation, upgrading of existing systems or accessories required, and the cost incurred, are the responsibility of the customer. [. . . ] This menu selects normal level of contrast. This menu selects reduced level of contrast. STANDARD SOFT 11. Normal ( N ) Button By pushing the Normal "N" button on the Remote Control while Picture or Sound Control Function is displayed, the selected function will be changed to the Normal Mode. Normalization will not occur if the function is not displayed when the "N" button is pushed. The Normal mode is the factory preset condition. Returning to this original condition is called "Normalization". 12. SOUND MENU Sound Menu Operation By pressing the SOUND MENU button, you can sequentially select the Sound menus as shown below: On-screen MUSIC SPEECH MOVIE Function For music programme for example. For movie programme for example. 99 WAKE UP TIMER OFF 13. WAKE UP Wake Up Timer Button 1. Press the " WAKE UP TIMER" button. Press the position left or right button to select the wake up timer. (Wake up timer will increase or decrease by 10 minutes when left or right button is pressed. ) Note : Wake up time can be set up to 12 hours. After setting the wake up timer, switch the TV set to stand-by mode. (LED light will blink ON and OFF during stand-by mode) 99 WAKE UP TIMER 00:10 11 General Operation 4. Re ­ activating the Automatic Frequency Tuning means allowing the set to automatically tune optimum tuning position, for that Channel Number. 1. Select the "AFC OFF" Channel Number which you want to return to Automatic Frequency Control (Cancel the manual fine tuning). 1 "AFC OFF" Channel Numbers are indicated to you by the " " symbol to the left of the Channel Number. 2. PRE. Press the " PRE. " (PRESET) buttons twice, setting the Preset Menu to set to "MANUAL TUNE" mode. MAIN MENU Press the "MAIN MENU" and "Position" buttons, until "MANUAL TUNE" function is selected. 1 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. CHANGE GEOMAGNETIC Manual Tune condition. 5. 5MHz AUTO OFF 1 8 3. Press the Volume Up " + " or Down " ­ " button briefly. 1 The best tuning position is automatically memorized. MANUAL TUNE ­­­­­­­­­­­­­­ M 1 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. CHANGE GEOMAGNETIC MAIN MENU Press the Position Left or Right button briefly. 5. 5MHz AUTO OFF 1 8 4. PRE. Press the "PRE" (PRESET) button 7 times. 1 This returns the set to the normal viewing condition. MAIN MENU Press the "MAIN MENU" button twice. 16 Tuning Procedure How to Skip Programme Number MAIN MENU PRE. TV/AV ­ + S-VIDEO VIDEO AV 2 IN 1, 4 ­ R ­ AUDIO 3 1 L/MONO OR 1, 4 3 PRE. 2 Press the " PRE. " (PRESET) button 6 times, setting the Preset Menu to "SKIP". 1. MAIN MENU Press the "MAIN MENU" and "Position" buttons, until the Preset Menu to "SKIP" . 1 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. CHANGE GEOMAGNETIC Channel Skip condition. 5. 5MHz AUTO OFF 1 8 2. Select a Programme Number you want to skip, by pushing the Channel number Up or Down buttons. 2 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. CHANGE GEOMAGNETIC 5. 5MHz AUTO OFF 2 8 3. Press the Volume Up " + " or Down " ­ " button. 2 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. CHANGE GEOMAGNETIC The displayed "OFF" condition changes to "ON". 5. 5MHz AUTO ON 2 8 MAIN MENU Press the Position Left or Right button. 4. PRE. Press the "PRE" button 3 times. This returns the set to the normal viewing condition. MAIN MENU Press the "MAIN MENU" button twice. 17 Tuning Procedure How to Cancel the Skip Function MAIN MENU PRE. TV/AV ­ + S-VIDEO VIDEO AV 2 IN 1, 4 3 ­ R ­ AUDIO L/MONO OR 1 1, 4 3 PRE. 2 Press the " PRE. " (PRESET) buttons 6 times, setting the Preset Menu to "SKIP". 1. MAIN MENU 1 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. CHANGE GEOMAGNETIC Channel Skip condition. 5. 5MHz AUTO OFF 1 8 Press the "MAIN MENU" and "Position" buttons, until "SKIP" is selected. 2. Select the skipped Programme Number, by pressing the Channel Number Up or Down buttons. 2 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. CHANGE GEOMAGNETIC 5. 5MHz AUTO ON 2 8 3. Press the Volume Up " + " or Down " ­ " button. 2 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. CHANGE GEOMAGNETIC The displayed "ON" condition changes to "OFF". 5. 5MHz AUTO OFF 2 8 MAIN MENU Press the Position Left or Right button. Repeat step 2 and 3, if you wish to cancel the Skip function on any other programme number. 4. PRE. After the Skip Cancel operation is completed, press the " PRE " button 3 times. This returns the set to the normal viewing condition. MAIN MENU After the Skip Cancel Operation is completed, press the " MAIN MENU " button twice. 18 Tuning Procedure Colour System Selection Use this function if a clear picture with weak colour is obtained when a Broadcast or AV signal is received. MAIN MENU PRE. TV/AV ­ + S-VIDEO VIDEO AV 2 IN 1, 3 ­ R ­ AUDIO L/MONO OR 2 1 1, 3 2 1. PRE. Press the " PRE. " (PRESET) button 4 times. 1 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. [. . . ] The on-screen language display will change as follows : 1 MAIN MENU PICTURE 25 Advanced Remote Control Transmitter Operation Preset Menu Operation Geomagnetism Correction Since a large picture tube has been used, blurring of colours and strange discolouration patches may occur depending on the direction the television faces. For optimum viewing, it is necessary to adjust the TV placement. 1. The Power should be off when determining the installation location and direction. At this time please verify what direction the TV screen is to face (direction indicated by the arrow). PRE. TV/AV ­ + S-VIDEO AV 2 IN VIDEO L/MONO ­ R ­ AUDIO 2. Press the "Main Power Switch" 3. MAIN MENU Press the "MAIN MENU" button. PICTURE "Main Menu" condition. 4. MAIN MENU Select the Preset Menu by using the Position Left or Right button. PRESET 5. MAIN MENU Select the Geomagnetic Mode by using the "Position" button. 88 PRESET AUTO TUNE MANUAL TUNE SOUND SYS COLOUR SYS FINE TUNE SKIP POS. [. . . ]