User manual PANASONIC TC-21M2R

[. . . ] Retain your purchase receipt also, and note down the Model Number and Serial Number of your set in the space provided on the rear cover of these Instructions. Caution Be careful not to scratch the surface of the screen. · Hard or sharp objects bumped or rubbed against the screen (when removing from package or during transport) may leave scratches. · To clean wipe the screen with a soft cloth. . 2 Table of Contents Warnings and Cautions Before Operating This Set 4~5 6~7 Connecting the Aerial Cable to the RF In Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connecting the Main plug to the Wall Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (2) If a clear picture with correct colours cannot be obtained when a Broadcast or AV signal is received, refer to the "Colour System Selection" operation on page 29. (3) After the Automatic tune is finished, push the Position Number "" button to confirm the tuning condition for each Position. If some Position Numbers are unused, it is possible to skip such Position Numbers. Please refer to the Position Number Skip operation on page 24. (4) Repeated pushing of the "PRE. " (preset) button changes the PRESET menu as follows; TV Mode (Normal viewing condition) AUTO TUNE (Page 18) MANUAL TUNE (Page 20) SOUND SYS (Page 28) POS. CHANGE (Page 25 ) SKIP (Page 24) FINE TUNE (Page 22) COLOUR SYS (Page 29) 19 Tuning Procedure Manual Tune PRE. TV/AV - + (TV set) 1, 4, 6 3, 5 1 PRE. Push the "PRE. " (preset) button 2 times. 2 ^ Push either the Position Number Up "" or Down "" button. 3 + Push the Volume Up "+" or Down "-" button. Volume "+" : Next higher Channel Volume "-" : Next lower Channel 4 PRE. Push the "PRE. " (preset) button. 20 ^ 2 ^ Manual Search MANUAL TUNE Condition. Select the desired Position Number. ^ Search Start. The best tuning position is automatically memorized. SOUND SYS Condition. Tuning Procedure 5 + If the sound is not clear or no sound is produced on a Position Number Position, push the Volume Up "+" or Down "-" button. Yo u m a y i m p r o v e t h e Sound quality. The sound indicator will change as follows. 4. 5MHz 6. 5MHz 5. 5MHz 6. 0MHz Note: When sound volume is too small to confirm, turn it up by using the sound volume button on the remote control. Push the "PRE. " (preset) button 5 times. This returns the set to the normal viewing condition. 6 PRE. Helpful Hint (1) If a clear picture cannot be obtained even when a Broadcast or AV signal is received, refer to the "Colour System Selection" operation on page 29. The TV set must first be switched on at the wall outlet and at the Power Switch. (Refer to page 7) Push this button to turn the TV set ON, from STANDBY mode. Push it again to turn the TV set OFF, STANDBY mode. Note: It is also possible to turn the TV set on STANDBY by pushing the "Direct Position Number Selection" buttons (0-9) and the "Position Number Up or Down" button, either on the set or on the Remote Control. PRE. TV/AV - + 2 (TV set) 5 4 2 1 6 3 8 R-TUNE TV/AV 7 5 2 3 1 4 7 + 2 5 8 0 3 6 9 + 4 3 1 2 VCR/LD/DVD VCR LD/DVD A DISC SIDE B 4 MAIN MENU SKIP N PICTURE MENU SOUND MENU SKIP P. AI SURROUND WAKE UP 9 10 5 26 ^ 8 + ^ ^ ^ Position Number Selection Push the Position Number Up "" or Down "" button to select the next higher or lower Position number. Direct Position Number Selection You can select the numbers directly by pushing "Number 0-9" button and the two digit Numbers by pushing "Two Digit" and "Position Number" buttons. , 1, 2 + Volume adjustment Push the Volume Up "+" or Down "-" button to increase or decrease the sound volume level. 12 TV/AV TV/AV mode Selection Push the "TV/AV" button to select TV, AV1, AV2, AV3 input signal modes sequentially. TV/AV General Operation 6 R-TUNE R-TUNE button Push this button to return the before Position. 9 WAKE UP WAKE UP button This button sets a timer to turn on the TV. The Wake Up time can be set in 10 minutes intervals and for up to 12 hours from the current time. Select the desired wake up time by using the Position Left "<" or Right ">" button. 7 SOUND MUTE button Push this button to mute the sound completely. The MUTE symbol will appear. When the timer turns on the TV, the TV will automatically set the off timer to turn the TV off after 90 minutes if you do not operate the TV after it is turned on. Note: (1) When the Wake Up timer is set, the Power Indicator blinks. (2) If the TV is left on with the Wake Up timer set, the timer setting is automatically deleted after a certain amount of time. Push the button once again to restore the previous sound level, and cancel the mute. 8 + RECALL button Push the RECALL button to display the current system status. Push again to cancel. 4 10 AUTO 4. 5MHz OFF TIMER button The TV set may be preset to switch to stand-by after a fixed period. [. . . ] Returning to this original condition is called "Normalization". 34 MAIN menu Operation FEATURES menu Operation MAIN MENU N 1. Select the FEATURES menu by pushing the Position Left "<" or Right ">" button and Access the FEATURES menu by pushing the Position Down "" button. Choose the option and adjust by pushing the Position Up "" or Down "" button, and by setting with the Position Left "<" or Right ">" button. PICTURE AI mode The PICTURE AI continuously detects fine differences in the picture signal, with great precision, and including the picture brightness, black level and contrast. This function Automatically adjusts the picture to the best quality for the scene, and reproduces images that provide a sense of depth. BLUE BACK mode When no picture signal is received, or the signal is weak, the screen reverts to a blue background colour and the Sound is muted. [. . . ]